Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
EP600 Subwoofer settings recommendations
#123232 01/07/06 01:27 AM
Joined: Jan 2006
Posts: 139
Richie Offline OP
veteran
OP Offline
veteran
Joined: Jan 2006
Posts: 139
Hi!

I joined the Axiom fraternity yesterday when I received my slightly modified 5.1 system. I got four M80ti speakers, one VP150 center speaker, and one EP600 subwoofer. They are being powered by a Denon 3805 AV receiver.

I know it has been only 24 hours, but the speakers do sound very good right out of the box. The Denon 3805 has no problems driving the four 4-ohm M80ti's and the 6-ohm VP150. Jean-Claude at Axiom had assured me over the phone that the Denon is powerful enough to handle the 4-ohm speakers even though their manual refers only to 6 and 8-ohm speakers.

I have read some of the recent postings about the EP600. I was wondering if members here have recommendations about the subwoofer settings to get deep bass without shaking the foundations of the house! I know a certain amount of experimentation will be needed before I get perfect bass.

Thanks!

P.S. When I move into my basement HT next year, I will get a pair of QS8's to have a 7.1 channel audio system. Also on the wish list - the Earthquake Cinénova Grande Seven-Channel Amplifier (300wpc x 7).


4 M80s/VP150/EP600/Denon AVR-5308 & DVD-2910/
2 QSC SRA3622(1100wattsX2)/Carvin 1800HD(600wattsX2)
Re: EP600 Subwoofer settings recommendations
#123233 01/07/06 02:54 AM
Joined: Jan 2004
Posts: 13,840
Likes: 13
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,840
Likes: 13
I have the 2805 and near the front of the manual it states not to drive speakers with below 4ohm, I'm sure the 3805 would be the same...

As far as the 600, the manual that comes with it gives you a good starting point. I have a huge room, and after calibration with an SPL meter, so far I have the following settings:

crossover knob: set to bypass as my receiver is managing the crossover of 80hz, all speakers set to small.

volume (gain): about the 8 o'clock position, the manual states to start about midway of 9 o'clock.

trim: set to flat as stated for a larger room.

phase: currently set to 0, you may have to experiment.

On my receiver I have the crossover set to 80hz and the dB level of the sub channel is on about -2dB. Have you calibrated with an SPL meter?

Welcome by the way and that is one bad system dude...

Randy


M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Re: EP600 Subwoofer settings recommendations
#123234 01/07/06 03:10 AM
Joined: Jan 2006
Posts: 139
Richie Offline OP
veteran
OP Offline
veteran
Joined: Jan 2006
Posts: 139
Randy:

Thanks for the advice. I have the EP600 at almost the same settings as you. I used a Denon microphone with the Denon 3805's built-in EQ program. It set the sub at -4.5dB. Looks like I am on the right path!

Richie

P.S. How do I list the Axiom goodies under my signature?


4 M80s/VP150/EP600/Denon AVR-5308 & DVD-2910/
2 QSC SRA3622(1100wattsX2)/Carvin 1800HD(600wattsX2)
Re: EP600 Subwoofer settings recommendations
#123235 01/07/06 03:23 AM
Joined: Jan 2004
Posts: 13,840
Likes: 13
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,840
Likes: 13
Click on "My Home" at the top of the forum, scroll down and click "edit" for your preferences, and update your signature. You are limited to so many characters though..

One thing you might try...I also use the microphone for my initial setup, and it did a pretty good job. I then bought an SPL meter from Radio Shack and re checked everything using the receivers Test Tone feature. I did make some adjustments, but it was pretty close. I did recheck the delay (distance) settings of the autosetup and found it had my sub a little off, so I manually adjusted that in the speaker setup menu.

As far as the room Eq, which is turned off by default, I tried it on at first but found it made my M60's have to much midrange, so I've left it off ever since.

welcome to our community... Randy



M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Re: EP600 Subwoofer settings recommendations
#123236 01/07/06 03:34 AM
Joined: Oct 2005
Posts: 212
local
Offline
local
Joined: Oct 2005
Posts: 212
Randy I know you have your CC at about 76/77 but what is your sub at? Mine is around 80. i thought 75 was not enough bang.


M60's VP150 QS8's EP500 Denon3805
Re: EP600 Subwoofer settings recommendations
#123237 01/07/06 03:40 AM
Joined: Jan 2004
Posts: 13,840
Likes: 13
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,840
Likes: 13
You should not be using the crossover on your sub if you are using the crossover in the receiver speaker setup menu. I have my Denon 2805 crossover at 80hz, and the sub crossover set to bypass. You don't want them conflicting with eachother...

Randy



M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Re: EP600 Subwoofer settings recommendations
#123238 01/07/06 03:44 AM
Joined: Oct 2005
Posts: 212
local
Offline
local
Joined: Oct 2005
Posts: 212
Let me repharse myself. What is your reading on your spl meter?


M60's VP150 QS8's EP500 Denon3805
Re: EP600 Subwoofer settings recommendations
#123239 01/07/06 03:49 AM
Joined: Jan 2004
Posts: 13,840
Likes: 13
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,840
Likes: 13
gotcha, when you said CC, I thought we were talking about Crossover, my mistake....

I'm with you, I first tried having my volume on the sub around 7 o'clock and the receiver was at about -2dB's, this was with and SPL of about 75/76 dBs. I have read where others like the sub a little hotter, so I have been experimenting. I think I have my receiver still on -2dB's, and have raised the sub volume to achieve about 80dB's like you have mentioned, which I believe is about 8 o'clock on the sub. I would have to recheck to make sure.

The other night a friend of mine brought over a DVD that had a bunch of DTS and Dolby sound demo's. There was one DTS track that blew both of our minds. There was also a Dolby track that when you closed your eyes, you felt like you were in an aquirium with bubbles popping all around you, it was amazing.

I love my 7.1 setup with my 4 Qs8's...


M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Re: EP600 Subwoofer settings recommendations
#123240 01/07/06 03:54 AM
Joined: Oct 2005
Posts: 212
local
Offline
local
Joined: Oct 2005
Posts: 212
Thanks Randy


M60's VP150 QS8's EP500 Denon3805
Re: EP600 Subwoofer settings recommendations
#123241 01/07/06 03:55 AM
Joined: Jan 2004
Posts: 13,840
Likes: 13
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,840
Likes: 13
One other thing I have forgot to mention is that I like to bump up my center channel at least 2 dB's higher than my M60's. If I use the meter and calibrate using 75dB's or if I use the built in microphone option, it always places my center channel a few dB's below my mains. During movies it is hard to hear the dialog at lower levels. If I crank it up then the other speakers blow you out of the room. I think others have mentioned they like to bump up the center as well.


M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Page 1 of 2 1 2

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,940
Posts442,457
Members15,616
Most Online2,082
Jan 22nd, 2020
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,840
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 145 guests, and 4 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4