Get Free, Friendly, Expert Advice
Call 1-866-244-8796 or email

Designed and Manufactured in Canada Since 1980


AxiomAudio Blog

Blind Listening Tests

Sneak Peek into Axiom’s Current Research and Development

Axiom’s Newest Speaker: The In-Ceiling M3

Wall'O'Fame
Greg's pseudo-HT room
EP175v4 with M3v4
Who's Online
1 registered (CV), 45 Guests and 4 Spiders online.
Key: Admin, Global Mod, Mod
Financing
Forum Stats
13348 Members
11 Forums
22992 Topics
406624 Posts

Max Online: 378 @ 02/24/13 04:33 PM
Top Posters
Ken.C 17816
pmbuko 16305
SirQuack 13351
CV 11311
MarkSJohnson 11002
Meanwhile On Facebook

Love this review by Brad C! "Very impressed with my purchase: 2 High Powered M6...

(y) Great review from Tom H of his new surround speakers! "I love the surroun...

22 year-old Axiom System, still in showroom condition! Welcome home, old friends!

The end of a truly unique voice. RIP Joe Cocker - you were part of the soundtr...

Topic Options
Rate This Topic
#2158 - 03/21/02 04:57 AM Question on the M50
Anonymous
Unregistered


Just a quick technical question for Ian or Alan (or somebody) redarding the design of the M50. Is this design technically a 2 way speaker system (i.e. only one crossover) or does it utilize a crossover between the two woofers as well as the tweeter. And while I am at it I guess the same could be asked about the M22 as well.
I ask - because I have found (in the past) that 2 way designs often sound more natural that 3 way designs - and I pretty much attributed it to the issue of the crossovers. Kinda simplistic, but it is an observation that has been pretty accurate (at least for me) for a long time.

Thanks,

Randyman

Top
#2159 - 03/21/02 06:25 PM Re: Question on the M50
BBIBH Offline
connoisseur

Registered: 01/10/02
Posts: 1064
Loc: Canada
Your viewpoint is well beleived in audio circles. However, there are more factors involved in differing sound than simply the crossover. I am not going to debate which sounds better, but will point out that cabinet volume, driver choice, crossover points, etc will make different speaker sizes sound different.

In actuality, most speakers of 3+ way desing have a single crossover. But there are multiple output points designed and used from the crossover. Think of a speaker as a very inefficient motor, which wastes most of your amplifier power! By allowing multiple drivers to work in certain areas (as decided by the crossover), each driver can work a little better in it's particular area. Crossovers can and do introduce other issues and problems as well. Designers can offset certain problems in other areas of the design - multiple drivers, etc.
_________________________
Regards,

Mike

Top
#2160 - 03/21/02 08:19 PM Re: Question on the M50
Anonymous
Unregistered


Appreciate your response, information, and input. Didn't intend to get into a discussion about the design principles. But since you started.... actually I understand (sorta) many of the variables involved for speaker design and that many speakers (drivers) have their own natural frequency roll-off and that in itself can act as a type of crossover, I was just curious anout the actual physical design because different roll-off frequencies and rates (6db, 9db, 12db/octive, etc) have a distinct effect on the sound (as well as the drivers). It was just that in my many years of listening and auditioning I had "discovered" that true 2 way speakers tended to sound more natural or cleaner to my ear, and all else being equal (even though it never is) I deduced that a significant factor to my listening experiences could well be the crossover. Funny eh?

Thanks!

Randyman

Top



Moderator:  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Home  |  Corporate Info  |  Products  |  Message Board  |  FAQs  |  Warranty  |  Site Map  |  Privacy Statement   |  Contact Us

©2014 Colquhoun Audio Laboratories Limited
All Rights Reserved.