Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 4 1 2 3 4
Amplifier hum
#382091 08/25/12 10:56 PM
Joined: Aug 2012
Posts: 8
G
regular
OP Offline
regular
G
Joined: Aug 2012
Posts: 8
I have just recently purchased a crown XLS1500 amplifier to be used with my Onkyo 875 receiver to power my front M80s. I didn't realize that the amp could only work with a 120 volt power supply. I only have 240 volt where I live. I then decided to try a cheap step down transformer to step 240v down to 120v. Suprising that this crown XLS1500 amp only draws max 250 watts yet claims to put out over 500 watts/channel into 4 ohms. Anyway that is a separate story.
With everything connected up I am getting a low frequency hum from the fronts. When I disconnect the rca input to the crown the hum disappears. It is only present when the onkyo receiver is on and the pre-amp out is connected to the crown amp.
Is there any way I can eliminate this hum or reduce it.
Should I use the XLR inputs on the Crown. To do this I would need to get an RCA to XLR adaptor. Is it possible this hum is caused by the step down transformer? I doubt it since the hum is not always present. Any ideas? confused

Last edited by grantlyt1; 08/25/12 10:57 PM.
Re: Amplifier hum
grantlyt1 #382092 08/25/12 11:08 PM
Joined: Sep 2004
Posts: 11,458
shareholder in the making
Offline
shareholder in the making
Joined: Sep 2004
Posts: 11,458
Is everything plugged into one outlet? It sounds like a ground hum which often pops up when interconnected devices are plugged into different outlets.

Try a cheater plug (no ground prong) to see if that makes the hum go away.


::::::: No disrespect to Axiom, but my favorite woofer is my yellow lab :::::::
Re: Amplifier hum
grantlyt1 #382095 08/25/12 11:23 PM
Joined: Aug 2012
Posts: 8
G
regular
OP Offline
regular
G
Joined: Aug 2012
Posts: 8
Yes everything is plugged into the one outlet. I even disconnected all devices and left only the receiver and amplifier connected but still the same problem.
Is the use of this cheater plug dangerous?

Re: Amplifier hum
grantlyt1 #382097 08/25/12 11:24 PM
Joined: Jan 2004
Posts: 13,840
Likes: 13
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,840
Likes: 13
Are all your outlets on the same circuit to the breaker? Might be a ground loop hum. If you have a sub, what happens if you unplug the interconnect?


M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Re: Amplifier hum
grantlyt1 #382099 08/25/12 11:25 PM
Joined: Sep 2004
Posts: 11,458
shareholder in the making
Offline
shareholder in the making
Joined: Sep 2004
Posts: 11,458
No, though it's better used as a diagnostic tool than a permanent solution.

Do you have a coax cable (TV, Cable) going into a device that's plugged into the receiver? If so, try disconnecting the coax cable.


::::::: No disrespect to Axiom, but my favorite woofer is my yellow lab :::::::
Re: Amplifier hum
SirQuack #382101 08/25/12 11:35 PM
Joined: Aug 2012
Posts: 8
G
regular
OP Offline
regular
G
Joined: Aug 2012
Posts: 8
Yes the outlets are on the same circuit breaker. Disconnecting the pre-amp out to the sub has no effect on the hum.

Re: Amplifier hum
grantlyt1 #382102 08/25/12 11:37 PM
Joined: Feb 2004
Posts: 1,863
connoisseur
Offline
connoisseur
Joined: Feb 2004
Posts: 1,863
Originally Posted By: grantlyt1

Should I use the XLR inputs on the Crown. To do this I would need to get an RCA to XLR adaptor. Is it possible this hum is caused by the step down transformer? I doubt it since the hum is not always present. Any ideas? confused


To get the true benefit of XLR connectors you're receiver/processor would have to have XLR outs... XLR's are a 3 wire system, RCA is a 2 wire system... To get rid of the hum, you need a true 3 wire system.

I had the same problem, i think it's the wiring in my house.. I am using all XLR connectors. However, my processor has XLR outputs....

By using a step down transformer, are isolating that outlet.
My money is on a ground loop problem. My house also have a ground loop... So, i have to deal with multiple electrical issues.....

Re: Amplifier hum
MarkSJohnson #382103 08/25/12 11:39 PM
Joined: Aug 2012
Posts: 8
G
regular
OP Offline
regular
G
Joined: Aug 2012
Posts: 8
I disconnected all inputs to the receiver but no difference however I just disconnected the hdmi out from the receiver and the hum is significantly reduced. Still annoying but much better. But I need to use this HDMI output.

Re: Amplifier hum
grantlyt1 #382105 08/25/12 11:40 PM
Joined: Feb 2004
Posts: 1,863
connoisseur
Offline
connoisseur
Joined: Feb 2004
Posts: 1,863
you may not have a good earth ground.... that is one other possibility.

Re: Amplifier hum
grantlyt1 #382107 08/26/12 12:20 AM
Joined: May 2003
Posts: 18,044
shareholder in the making
Offline
shareholder in the making
Joined: May 2003
Posts: 18,044
Where do you live? I would wager that this has something to do with the step down transformer.

Guys, if he's got 240V, I doubt they even have cheater plugs...


I am the Doctor, and THIS... is my SPOON!
Re: Amplifier hum
Ken.C #382110 08/26/12 12:50 AM
Joined: Aug 2012
Posts: 8
G
regular
OP Offline
regular
G
Joined: Aug 2012
Posts: 8
I live in Australia. I have never seen these cheater plugs.

Re: Amplifier hum
grantlyt1 #382112 08/26/12 12:58 AM
Joined: May 2003
Posts: 18,044
shareholder in the making
Offline
shareholder in the making
Joined: May 2003
Posts: 18,044
Yeah, I suspect they don't have them there. It's a legacy thing in the States from before we had grounded outlets--a lot of places still don't have them. Basically it disables the ground.


I am the Doctor, and THIS... is my SPOON!
Re: Amplifier hum
grantlyt1 #382114 08/26/12 01:31 AM
Joined: Jul 2009
Posts: 2,281
connoisseur
Offline
connoisseur
Joined: Jul 2009
Posts: 2,281
Unless you plan on using the amp in your shower just buck the ground off . Hell my new yamaha reciever came with no ground on the plug. It could also be a polarity problem , house wired incorrectly. Also change out the rca cables, i had a set i used from my kids car that were not that old and they were making my sub hum.


DOG is GOD spelled backwards.
What others think of me is none of my business.
M80 V3 MY GLOSS Cherry
Re: Amplifier hum
Gr8_White_North #382117 08/26/12 01:47 AM
Joined: Aug 2012
Posts: 8
G
regular
OP Offline
regular
G
Joined: Aug 2012
Posts: 8
I could easily take the ground pin off the 120v side of the plug. It already looks a bit loose. Is it really not that risky to power without the earth pin? I did already try another rca cable but same result. I could purchase a US cheater plug and use it on the 120 volt plug into the step down transformer.

Re: Amplifier hum
grantlyt1 #382118 08/26/12 01:52 AM
Joined: Jul 2009
Posts: 2,281
connoisseur
Offline
connoisseur
Joined: Jul 2009
Posts: 2,281
i have no grounds on my kit. i just went through this bs over the past week. You can use it as a test then buy a ground loop isolator if your concerned. You could modify an extension cord also. here are some hum eliminators to look at .

https://www.google.ca/search?q=hum+elimi...120&bih=613

Last edited by Socketman; 08/26/12 01:54 AM.

DOG is GOD spelled backwards.
What others think of me is none of my business.
M80 V3 MY GLOSS Cherry
Re: Amplifier hum
grantlyt1 #382119 08/26/12 01:53 AM
Joined: May 2003
Posts: 18,044
shareholder in the making
Offline
shareholder in the making
Joined: May 2003
Posts: 18,044
It is significantly more hazardous with 240V than 120V, but if you're doing it on the 120V side, it shouldn't be THAT big a deal.


I am the Doctor, and THIS... is my SPOON!
Re: Amplifier hum
Ken.C #382120 08/26/12 01:55 AM
Joined: Jul 2009
Posts: 2,281
connoisseur
Offline
connoisseur
Joined: Jul 2009
Posts: 2,281
Originally Posted By: Ken.C
It is significantly more hazardous with 240V than 120V, but if you're doing it on the 120V side, it shouldn't be THAT big a deal.


just wear rubber boots when operating the stereo grin


DOG is GOD spelled backwards.
What others think of me is none of my business.
M80 V3 MY GLOSS Cherry
Re: Amplifier hum
grantlyt1 #382121 08/26/12 02:19 AM
Joined: May 2002
Posts: 10,654
shareholder in the making
Offline
shareholder in the making
Joined: May 2002
Posts: 10,654
Grantly, welcome. If you mean that there was no hum problem previously with the 875 used for power, and if the connections(with the exception of the Crown connection)were the same, then there appears to be nothing new to create a ground loop. It's possible that there's a defect(e.g., rectifier, filter capacitors)in the power supply section of the Crown.

If it would be a ground loop, using a RCA/XLR adaptor wouldn't be helpful. As Alex pointed out, the balanced circuitry is entirely different, and doesn't simply involve the difference between a RCA plug and XLR connector. The sending unit(875)would have to have a balanced output with two voltages(of opposite polarity)rather than one, which the 875 doesn't have. The wiring itself is just one element and is meaningless without both balanced output circuitry and balanced input circuitry.

Incidentally, although you say that the Crown draws 250 watts "max", that's highly unlikely. Unless a power consumption number is specifically termed "full power" or similar language, the number given is an average one rather than max. Typically, 1/8th of full power is used for the average. For example, 1/8th of 500 is a bit over 60 watts, and at 1/8th power class AB amplifiers are on the order of 20-25% efficient(about 50% at full power). 60 watts output would therefore need about 250 watts of consumption. There's no inconsistency when manufacturers show a consumption number lower than the maximum output number.


-----------------------------------

Enjoy the music, not the equipment.


Re: Amplifier hum
JohnK #382123 08/26/12 03:03 AM
Joined: Aug 2012
Posts: 8
G
regular
OP Offline
regular
G
Joined: Aug 2012
Posts: 8
Problem solved! I just bought a ground loop isolator and the hum is entirely gone. Thanks everyone for your help. grin

Johnk- I am only using a stepdown transformer rated for 500 watts. Does this mean I may blow an fuse on it if I run the amp close to its upper limits?

Re: Amplifier hum
grantlyt1 #382124 08/26/12 03:12 AM
Joined: Feb 2004
Posts: 1,863
connoisseur
Offline
connoisseur
Joined: Feb 2004
Posts: 1,863
Originally Posted By: Ken.C
I would wager that this has something to do with the step down transformer.


Ken, this is highly likely...Due to the transformer in the the mix this, in of it self could also be the source of the ground loop as this is a new device, and does not address the grounding of that circuit...

How did you wire the ground? If you could post a schematic of how you wired the outlet with the transformer that would help. At this point everyone is hypothesizing as to what you did...


lol... this is what i was just writing as you posted the solution..... oh well!!


With this being said, i would bet the source of your ground loop is the wiring of the outlet off of the transformer.. Again, if you can post a schematic we could help eliminate the ground loop.....

Last edited by dakkon; 08/26/12 03:16 AM.
Re: Amplifier hum
grantlyt1 #382126 08/26/12 03:19 AM
Joined: May 2002
Posts: 10,654
shareholder in the making
Offline
shareholder in the making
Joined: May 2002
Posts: 10,654
The transformer could be burned out by lengthy operation at that power. What you would "blow" would more likely be your hearing in that case. The M80s are slightly above average in sensitivity and use about 1 watt for a comfortably loud average level. Brief peaks use a lot more, but are unlikely to need more than about 100 watts, which your 875 can easily handle.


-----------------------------------

Enjoy the music, not the equipment.


Re: Amplifier hum
grantlyt1 #382129 08/26/12 03:49 AM
Joined: Jul 2009
Posts: 2,281
connoisseur
Offline
connoisseur
Joined: Jul 2009
Posts: 2,281
Which ground loop isolator did you get.


DOG is GOD spelled backwards.
What others think of me is none of my business.
M80 V3 MY GLOSS Cherry
Re: Amplifier hum
Gr8_White_North #382130 08/26/12 04:03 AM
Joined: Aug 2012
Posts: 8
G
regular
OP Offline
regular
G
Joined: Aug 2012
Posts: 8

Re: Amplifier hum
grantlyt1 #382142 08/26/12 06:38 PM
Joined: Jan 2004
Posts: 13,840
Likes: 13
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,840
Likes: 13
try unplugging the sub from the wall outlet.


M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Re: Amplifier hum
SirQuack #409051 12/24/14 02:25 PM
Joined: Apr 2012
Posts: 350
Likes: 3
J
devotee
Offline
devotee
J
Joined: Apr 2012
Posts: 350
Likes: 3
I realize this is a well beaten subject but I have a hum present in my Theatre and have not been able to eliminate it.
If I unplug the Sub from the outlet the hum is gone. Plugging the sub into a different circuit/outlet did not remove the hum. Removing the grounding screw from the Amplifier plate on the back of the sub did not help, there is an Axiom audio ground isolator in line for the cable box.
I do not use XLRs for connections.
Am out of ideas!
Any thoughts on how to proceed?

thanks, Jeff
ps- Happy Holidays

Re: Amplifier hum
grantlyt1 #409053 12/24/14 03:28 PM
Joined: Mar 2014
Posts: 1,593
Likes: 1
A
connoisseur
Offline
connoisseur
A
Joined: Mar 2014
Posts: 1,593
Likes: 1
Assuming your sub cable is decent and not vaccum abused:

Any recent changes in back of your reciever? Cables shorting perhaps? HDMI and other connections ok? Definitely seems like a stray signal or filtering issue somewhere in the chain.

I had a similar issue develop over time using an extended sub cable joined with an rca butt connector. Got grumpy with time.

I would do a hard shutdown (unplug your receiver) and reterminate if issue persists. Failing that, call axiom.

Best of luck. smile

Edit: can you run a cable direclty from your bluray/dvd/cdplayer to the sub to rule out a huge chunk of the signal chain. Even an ipod on batteries connected directly would be a good elimination test. Make you turn the sub volume off first and slowly turn up if you connect a device with no variable output. Really loud! laugh been there!

Last edited by Serenity_Now; 12/24/14 03:36 PM.
Re: Amplifier hum
grantlyt1 #409058 12/24/14 05:18 PM
Joined: Sep 2011
Posts: 1,767
E
connoisseur
Offline
connoisseur
E
Joined: Sep 2011
Posts: 1,767
My hum was caused by my 'Cable TV' System - very, very common.

For trouble shooting, try disconnecting it at the 'F Connector' where it first joins your system.

My previous Velodyne Subs hummed until I made a jumper cable to kill it. With my EP800s, unscrewing the ground screw worked - much easier...

TAM

Re: Amplifier hum
grantlyt1 #409063 12/24/14 05:43 PM
Joined: May 2014
Posts: 1,170
Likes: 6
M
MMM Offline
connoisseur
Offline
connoisseur
M
Joined: May 2014
Posts: 1,170
Likes: 6
I had a hum between my Axiom LFR1100 DSP and my Anthem MCA5 amp. Even with nothing else hooked up (no source) it gave a hum. Fixed it by moving to XLR cables.

it is in the way that the ground is isolated, and Axiom did it a different way than the Anthem people and thus caused the hum. You might find it's the same with your new receiver.


Anthem: AVM60, Fosi DAC-Q5
Axiom: ADA1500, LFR1100 Actiive, QS8, EP500, M3, M3comp, M5
Re: Amplifier hum
MMM #409071 12/24/14 07:45 PM
Joined: Apr 2012
Posts: 350
Likes: 3
J
devotee
Offline
devotee
J
Joined: Apr 2012
Posts: 350
Likes: 3
So I disconnected the coax cable from the Comcast cable box, no change, unplugged the cable box, no change in the hum.
WT_!
Found a 3 prong to 2 prong electrical adapter in my tool box, put it in place and no hum, none what so ever, nada, zilch, nicht!
Lucky me, back to COD or the Nut Cracker Suite.
Thanks for the suggestions!
Jeff

Re: Amplifier hum
grantlyt1 #409073 12/24/14 08:49 PM
Joined: Sep 2011
Posts: 1,767
E
connoisseur
Offline
connoisseur
E
Joined: Sep 2011
Posts: 1,767
Great!

It is really good for one's mental health when hum finally disappears...

TAM

Re: Amplifier hum
Jeff_in_the_D #409147 12/29/14 01:41 PM
Joined: Dec 2007
Posts: 257
local
Offline
local
Joined: Dec 2007
Posts: 257
Originally Posted By: Strider53
So I disconnected the coax cable from the Comcast cable box, no change, unplugged the cable box, no change in the hum.
WT_!
Found a 3 prong to 2 prong electrical adapter in my tool box, put it in place and no hum, none what so ever, nada, zilch, nicht!
Lucky me, back to COD or the Nut Cracker Suite.
Thanks for the suggestions!
Jeff


That implies there is a wiring irregularity. I would have that checked.


Mark
Pio 94,SB3,BD30,A35,Pio 48AV.Pronto 7000 controlling all. Getting ready for 22s, 150 & QS8s.
Page 1 of 4 1 2 3 4

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,940
Posts442,457
Members15,616
Most Online2,082
Jan 22nd, 2020
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,840
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 386 guests, and 4 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4