Get Free, Friendly, Expert Advice
Call 1-866-244-8796 or email

Designed and Manufactured in Canada Since 1980


AxiomAudio Blog

Blind Listening Tests

Sneak Peek into Axiom’s Current Research and Development

Axiom’s Newest Speaker: The In-Ceiling M3

Wall'O'Fame
Experimental Atmos
Greetings fellow Axiom owners...
Who's Online
2 registered (nickbuol, Socketman), 54 Guests and 6 Spiders online.
Key: Admin, Global Mod, Mod
Financing
Forum Stats
13329 Members
11 Forums
22920 Topics
405210 Posts

Max Online: 378 @ 02/24/13 04:33 PM
Top Posters
Ken.C 17789
pmbuko 16289
SirQuack 13340
CV 11236
MarkSJohnson 10942
Meanwhile On Facebook

Did you get your "Golden Email"? The great gift certificate email giveaway star...

Here's a helpful article for everyone looking at putting a new stereo or home th...

Interesting article about who's getting the money from streaming radio services...

Topic Options
Rate This Topic
#392265 - 04/21/13 05:27 PM Crossover setting for VP180 at 40hz?
VoicOfReason Offline
old hand

Registered: 04/19/12
Posts: 78
Loc: Northwest Arkansas
I have always left my VP180 center channel at 60hz crossover. Well, the other day I was re-running Audyssey and accidentally set the center to large and the front M80's to small. I noticed a very nice improvement in the sound. The center sounded more full and rich. I know the best advice is NOT the set the center to FULL, but what about 40hz while leaving the M80's at 60hz?

Does anyone here use this as their default setting?

Any disadvantages?

Thoughts?



Edited by VoicOfReason (04/21/13 05:30 PM)
_________________________
Epson 8350 * Denon 4311CI * XPA-5 * M80/VP180 * 2 QS8's+M2v3-DSX * SVS PC13-Ultra ** Buttkicker LFE

Top
#392276 - 04/21/13 09:25 PM Re: Crossover setting for VP180 at 40hz? [Re: VoicOfReason]
JohnK Offline
shareholder in the making

Registered: 05/11/02
Posts: 10405
Peter, some clarification of what you in fact did is necessary. When the front speakers are set "Small", none of the other speakers, including the center, can be set "Large".
_________________________
-----------------------------------

Enjoy the music, not the equipment.



Top
#392284 - 04/21/13 10:43 PM Re: Crossover setting for VP180 at 40hz? [Re: JohnK]
VoicOfReason Offline
old hand

Registered: 04/19/12
Posts: 78
Loc: Northwest Arkansas
Sorry. Yes, you are correct. It was the crossover I set wrong at first. The center was at 40hz and fronts were at 60hz. It sounds better this way, I think. Any disadvantages? Do soundtracks usually even send a lot of LFE/low level information to the center channel anyway?
_________________________
Epson 8350 * Denon 4311CI * XPA-5 * M80/VP180 * 2 QS8's+M2v3-DSX * SVS PC13-Ultra ** Buttkicker LFE

Top
#392288 - 04/21/13 11:02 PM Re: Crossover setting for VP180 at 40hz? [Re: VoicOfReason]
SirQuack Offline
shareholder in the making

Registered: 01/29/04
Posts: 13340
Loc: Iowa
Also, you never want to lower the crossover (ok to set higher) from the setting that was configured by your receiver after running Audyssey. For ex, if Audyssey reports back to your Denon that the -3dB point of a particular speaker is 80Hz, the Denon would set the speaker as "small" with an 80Hz crossover, as Denon uses 40Hz as the determining factor. You would never lower that value, but raising is ok.
_________________________
M80s-VP180-QS8s-EP600-2xEP350 Denon3808 Outlaw7700
M22-OWM22-VP100-Denon2805
Audio Nirvana

Top
#392290 - 04/21/13 11:26 PM Re: Crossover setting for VP180 at 40hz? [Re: VoicOfReason]
nickbuol Online   content
connoisseur

Registered: 09/16/04
Posts: 4516
Loc: Marion, IA
My Onkyo receiver sets my VP180 to 40hz every time I've run it. Some time I leave it, sometimes I bump it up to 60 or 80hz. Like Randy states, that is OK, wit Audyssey because you are basically removing calibration extension in the lower frequencies. However, if it sets something to, say, 80hz, and you drop it down to 60hz, Audyssey hasn't done any room calibration down between the original 80hz and your new 60hz setting.
_________________________
http://ht.buol.us
M60s, VP180, VP150, QS8s, SVS 20-39PCi, HTPC, JVC RS45, Onkyo TX-NR709, Shakers

Top
#392291 - 04/22/13 01:44 AM Re: Crossover setting for VP180 at 40hz? [Re: nickbuol]
VoicOfReason Offline
old hand

Registered: 04/19/12
Posts: 78
Loc: Northwest Arkansas
Yeah, Audyssey sets everything in front to 40hz default, for me.
_________________________
Epson 8350 * Denon 4311CI * XPA-5 * M80/VP180 * 2 QS8's+M2v3-DSX * SVS PC13-Ultra ** Buttkicker LFE

Top
#392296 - 04/22/13 06:24 AM Re: Crossover setting for VP180 at 40hz? [Re: VoicOfReason]
nickbuol Online   content
connoisseur

Registered: 09/16/04
Posts: 4516
Loc: Marion, IA
It sets my M60s to 60hz in comparison.
_________________________
http://ht.buol.us
M60s, VP180, VP150, QS8s, SVS 20-39PCi, HTPC, JVC RS45, Onkyo TX-NR709, Shakers

Top



Moderator:  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Home  |  Corporate Info  |  Products  |  Message Board  |  FAQs  |  Warranty  |  Site Map  |  Privacy Statement   |  Contact Us

©2014 Colquhoun Audio Laboratories Limited
All Rights Reserved.