![](/boards/images/icons/default/book.gif) Re: EP350v3, EP600 and 15" Velodyne
|
Joined: Aug 2007
Posts: 3,488 Likes: 9
connoisseur
|
connoisseur
Joined: Aug 2007
Posts: 3,488 Likes: 9 |
Is that the 400+ pounds sub? Geez. I hope you will be allowed to borrow one of Purolator's van for this! And maybe a lift too? ![smile \:\)](/boards/images/graemlins/default/smile.gif)
See Mojo's signature
|
|
|
![](/boards/images/icons/default/book.gif) Re: EP350v3, EP600 and 15" Velodyne
|
Joined: Oct 2005
Posts: 853
aficionado
|
aficionado
Joined: Oct 2005
Posts: 853 |
Nice report Jason and Mojo. That Velodyne DLS-5000R is a real departure for Velo and I suspect just a made in China sub labelled Velodyne for sale through the big box stores. Products like this just hurt the brand. I've never liked subs with big unflared slot vents because of all the noise inherent with that type of port. In addition FR is anything but linear, in fact its more humped than even the old SVS models. Worse, its THD doesn't decline to less than 10% until 30hz and above. No surprise it sounds so bad. ![sick](/boards/images/graemlins/default/sick.gif) Judging by your and other reports, the EP350v3 appears to be a real winner especially at that price. It may not go as deep as a EP600 but a pair of 350v3 would be an excellent alternative and perhaps better than a single 600 because of all the additional benefits you get from dual subs. I have to find a pair to audition.
John
|
|
|
![](/boards/images/icons/default/book.gif) Re: EP350v3, EP600 and 15" Velodyne
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
I'll have to do more testing. Not sure I would go as far to say the 350 does a better job than my 600, maybe mojo's sub is defective. Keep in mind, I do believe his 600 has the new firmware with the brickwall higher. Mojo, didn't you tell me once via PM your previous 600 performed better than your new altered one?
My twin 350v3's in Ebony are killer and they continue to suprise me on punch and how low they will go. I'll keep testing and going back/forth between the two.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
![](/boards/images/icons/default/book.gif) Re: EP350v3, EP600 and 15" Velodyne
|
Joined: Jan 2007
Posts: 10,490 Likes: 116
shareholder in the making
|
OP
shareholder in the making
Joined: Jan 2007
Posts: 10,490 Likes: 116 |
No, I have the old firmware...same as yours.
House of the Rising Sone Out in the mid or far field Dedicated mid-woofers are over-rated
|
|
|
![](/boards/images/icons/default/book.gif) Re: EP350v3, EP600 and 15" Velodyne
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
Ok, I was thinking you had said you disabled the original amp when trying to upgrade yourself. And the replacement was revised at the factory with initial feedback as being worse than your original amp.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
![](/boards/images/icons/default/book.gif) Re: EP350v3, EP600 and 15" Velodyne
|
Joined: Jan 2007
Posts: 10,490 Likes: 116
shareholder in the making
|
OP
shareholder in the making
Joined: Jan 2007
Posts: 10,490 Likes: 116 |
The replacement amp that Axiom sent me had the original firmware. The only thing that is different in my 600 now is the driver. I have the driver that is made with dull rather than shiny aluminum. The dull aluminum doesn't go as well with my beaver ![smile \:\)](/boards/images/graemlins/default/smile.gif) . I replaced the driver due to noise at lower frequencies with high SPLs. The noise is no longer there.
House of the Rising Sone Out in the mid or far field Dedicated mid-woofers are over-rated
|
|
|
![](/boards/images/icons/default/book.gif) Re: EP350v3, EP600 and 15" Velodyne
|
Joined: Sep 2004
Posts: 11,458
shareholder in the making
|
shareholder in the making
Joined: Sep 2004
Posts: 11,458 |
The dull aluminum doesn't go as well with my beaver I pity new forum members trying to figure that one out! ![smile \:\)](/boards/images/graemlins/default/smile.gif)
::::::: No disrespect to Axiom, but my favorite woofer is my yellow lab :::::::
|
|
|
![](/boards/images/icons/default/book.gif) Re: EP350v3, EP600 and 15" Velodyne
|
Joined: Dec 2007
Posts: 7,786
axiomite
|
axiomite
Joined: Dec 2007
Posts: 7,786 |
Meh, all us Canucks have a beaver or two somewhere in the livingroom...
Fred
------- Blujays1: Spending Fred's money one bottle at a time, no two... Oh crap!
|
|
|
![](/boards/images/icons/default/book.gif) Re: EP350v3, EP600 and 15" Velodyne
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
Is it the inflatible type or the real deal. ![smile \:\)](/boards/images/graemlins/default/smile.gif)
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
![](/boards/images/icons/default/book.gif) Re: EP350v3, EP600 and 15" Velodyne
|
Joined: Dec 2003
Posts: 10,420
shareholder in the making
|
shareholder in the making
Joined: Dec 2003
Posts: 10,420 |
Some are furry, others are shiny or smooth.
Jason M80 v2 VP160 v3 QS8 v2 PB13 Ultra Denon 3808 Samsung 85" Q70
|
|
|
Forums16
Topics24,945
Posts442,473
Members15,617
|
Most Online2,082 Jan 22nd, 2020
|
|
0 members (),
375
guests, and
5
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|