Axiom Home Page Forums General Discussion Home Theater need help with new Denon 3805

1st post. Have axiom speaker and am realy happy with them, it's the new (7 months old) Denon 3805 that has me pissed.
Great unit when it works. Super remote, when it works. I've been reconnection, reprogramiming, and resetting for the last several month.
Problem is that when i change sources there is no ouput. if I turn the thing off-back on it works if i change the soucre (vcr to dvd) there is no output again. Sometime if I go backto the original source it will work most time it dosen't

the remote has been hit or miss. Any comment or help would be greatly appriciated.

Thanks

Doctor, welcome. My first thought would be to try to determine if the problem is in the remote(more likely)or the receiver itelf. Have you tried changing sources using the controls on the receiver rather than using the remote? Does the same problem occur?

i've noticed something similar on my 3805 if i'm switching from SACD to regular CD. if i take out a SACD and the reciever is in the EXT mode and then i put in a redbook CD it won't put out any sound. i have to hit the I. Mode (or whatever it's labelled as) button on the remote and then it switches over and plays. i don't know if that's whats going on with your situation, but i suppose it can't hurt to try.

Hey Guys! I have a Denon 2805 and it does all the things you have mentioned. Yes you have to hit the mode button to change formats, but still you can have the same problem...the revceiver cannot seem to lock in, hence no audio. At one point I had to unplug my Denon 1910 dvd player. After plugging it back in and resetting all functions it seemed to work fine for a while but its back to its old tricks. Notice I said dvd player. Seems to me my problems started after I switched to a audio co-axial interconnect. I have been meaning to change back to analog to see if my suspicions are correct. Hope this helps in ferreting out the problem.

Also anyone have problems assigning surround modes for specific cd or dvd recordings? Seems that this appeared at the same time as the above. Same remedy?

Tom

Try going into the Set Up menu and making sure that you have the mode set to "Auto".

Bingo! That was my first thought too.

"Auto" enabled. Posted similar to this in "tech advice" no-one
was able to help. Then this thread started......imagine!

Tom

The forum works in mysterious ways sometimes.

In reply to:

---

"Auto" enabled.

---

Was this the solution?

No solution as of yet.

Tom

It doesn't seem likely that the 3805 is the culprit. I'd bet that it is either a receiver setting issue or a remote button selection issue.

The next time it happens, hit the "display" button (on the remote) and check what comes up on the tv screen or front panel and you will see what the receiver sees as its bio for that particular input. It should tell you if it is in "auto", "analog", "ext.in"...etc.

You guys have probably already checked this but are all of the digital inputs (in the receiver menu) correctly assigned and have you tried using a different type (coax/optical) of input for said component? I had to ask...

Could the receiver somehow be seeing "ext. in"? If the "ext. in" has been engaged with the remote, the receiver will stay in "ext.in"mode (no matter which source you switch to) until it is manually disengaged.....I think.

Rarely but sometimes, after I've used the "skip ahead" button (in rapid fire) on my sat. receiver, it (3805) drops the signal but I can get it back instantly by selecting the DBS source input again.

I'm now very curious as to what the problem could be. I know it is possible but I've never read of a Denon receiver needing a repair for this kind of problem, much less two of them.

You could also try asking the pros and forum members over at Audioholics. I bet you could get some good advice there as well.

Good luck! And keep us Denon owners posted.