Previous Thread
Next Thread
Print Thread
Rate Thread
newb question re: HT room prep'ing
#116750 11/21/05 05:31 AM
Joined: Nov 2005
Posts: 3
plummer Offline OP
newbie
OP Offline
newbie
Joined: Nov 2005
Posts: 3
Hi all, new to this board so take it easy on me . Anyways, currently contructing my basement of my two-storey and will have a dedicated HT room. Since I am strictly a newb with the lastest and greatest in TV's....i am not sure what I should do for in-wall wiring. I will probably be getting a plasma once things get completed and will mount on the wall, however yeah I dont' want wires running all over the place. I will be doing the speaker wiring and all that right away....but need some direction for a plasma. Any help is greatly apprectiated! Thx.



Re: newb question re: HT room prep'ing
#116751 11/21/05 05:34 AM
Joined: Jan 2004
Posts: 13,840
Likes: 13
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,840
Likes: 13
Could you post a drawing or picture of your room specifications/dimensions. It is very smart to think about these things now in early construction, your on the right track.

"welcome to the jungle"

Randy



M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Re: newb question re: HT room prep'ing
#116752 11/21/05 05:43 AM
Joined: Nov 2005
Posts: 3
plummer Offline OP
newbie
OP Offline
newbie
Joined: Nov 2005
Posts: 3
wow....(lol). Thanks for the immediate response! My basement is kind of in disarray right now but I will be moving stuff around in the next day or two to get ready for insulation/speaker wiring. Pics would probably be a waste because all I have done are my outside walls....but i just did dimensions and it will be 13 wide by 18 long. Obviously the one 13 wide wall will be the one housing the plasma. Hope this is enough! Thx again.

Re: newb question re: HT room prep'ing
#116753 11/21/05 05:19 PM
Joined: Jul 2005
Posts: 353
devotee
Offline
devotee
Joined: Jul 2005
Posts: 353
18'x13'

If at this stage you are only concerned with how and what type of cabling to use, make sure that the cable is rated to be installed in wall and if you are not 100% sure about the inputs of your current future display device, then install both HDMI and component video cables (s-video?). I'd also highly recommend cable shields to be installed at each cable penetration through the studs.


Where is your source equipment to be placed? Directly below the plasma or off in a remote closet?

Re: newb question re: HT room prep'ing
#116754 11/22/05 01:04 AM
Joined: Nov 2005
Posts: 3
plummer Offline OP
newbie
OP Offline
newbie
Joined: Nov 2005
Posts: 3
ok.....i'll do a google search as to what HDMI is. Basically what i'd like to know is that if I did plasma...then what type of cables should I run. I 'may' consider a projector....but that would require a different setup (obviously).
Is there a link to a certain cable shield? I'm not sure what they look like.
My components will probably be on the opposite side of the room in my furnace room. Any recommendations as to what type of RF to use ? THanks again. (yes, i am a newb).


Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,940
Posts442,457
Members15,616
Most Online2,082
Jan 22nd, 2020
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,840
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 145 guests, and 4 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4