Get Free, Friendly, Expert Advice
Call 1-866-244-8796 or email

Designed and Manufactured in Canada Since 1980

AxiomAudio Blog

Axiom’s New Computer Speakers

Blind Listening Tests

Sneak Peek into Axiom’s Current Research and Development

Solarrdadd's 7.1 Apartment HT!
A promise is A promise... Axiom's second home
Who's Online
1 registered (St_PatGuy), 40 Guests and 8 Spiders online.
Key: Admin, Global Mod, Mod
Forum Stats
13359 Members
11 Forums
23076 Topics
408005 Posts

Max Online: 378 @ 02/24/13 04:33 PM
Top Posters
Ken.C 17841
pmbuko 16319
SirQuack 13356
CV 11385
MarkSJohnson 11061
Meanwhile On Facebook

⚠ Only 5 days left in our Computer Speaker Presale!

(y) Love this review a customer sent us recently: "Bottom line, these speakers...

❔ The new M1 High Powered Computer Speaker uses Axiom's latest full one-inch twe...

High Powered Computer Speaker - Preorder Sale!

Page 2 of 2 < 1 2
Topic Options
Rate This Topic
#148590 - 10/04/06 11:24 AM Re: New Amp Humm / Noise [Re: Juggernaut850]
alan Offline

Registered: 01/29/02
Posts: 3193
Loc: Toronto/New York/Dwight

The white noise at full volume setting over headphones is normal "thermal" transistor noise and you'll hear some of that over headphones from any solid state preamp or amp aat full gain or volume. However, hum should not be present at all. Did you disconnect the separate ground wire to your power amp when you did the headphone hum test?

If so, and the hum is still present in the headphones, then yes, I think the preamp's power supply board is defective or there is a cold solder joint on a board. If it's under warranty, let the service guy find the problem and fix it. If the hum in the headphones ceases when you disconnect the ground wire to your power amplifier, then there is nothing wrong with your preamp.

Solid state preamps using the headphone jack should have NO audible noise or hiss at normal volume control settings.
Alan Lofft,
Axiom Resident Expert

#148591 - 10/07/06 08:52 PM Re: New Amp Humm / Noise [Re: Juggernaut850]
aabouganem Offline
old hand

Registered: 12/27/04
Posts: 81
Loc: Houston, Texas, USA
Wow... long time I have since my last "browse" in the Axiom BB... well, it feels good to be read the post again...


I have a T163 as well with an Outlaw 770. I have the same issue. Is your T163 brand new, I mean, the V2? Because mine was the previous model (not V2), and when I send it for the upgrade, the noise that you are experiencing became worst. In stereo mode is very subtle, but is multichannel, is audible in a room at normal listening level (I have friend that did not hear it, it will depend a lot on your ears). BTW, the V2 upgrade allows for bass management, and replace the HDCD decoding card and replace it for the DOLBY PLIIx. If your DVD/CD player plays HDCD, you lose nothing thru the analog output.

I could never get rid of the noise on my setup. I purchase a Monster clean power, and nothing. But I had a mess of cables, and I always tought it was because of that. Plugging the ICBM on the chain just made it worst. I have the EP500, but I never detected the noise on the sub after I loosen the screw on the back plate.

I have to say, that since the upgrade, the noise appeared. Does your T163 "clicks" when changing surround modes? Is a small 'click' I hear when I am not playing something and the volume level is high enough (> -15dB).

Well, I am sorry I did not contribute a bit on solving your issue, but at least you are not the only one with noise on the T163. Maybe arranging the cables/ground/etc reccomended on this BB will improve it.

I havent heard my setup since April (2006) as I moved out of the US and my rig is on storage at my home country Venezuela, where I am neither at this moment. I miss so much my AXIOM !!!!!

Page 2 of 2 < 1 2

Moderator:  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Home  |  Corporate Info  |  Products  |  Message Board  |  FAQs  |  Warranty  |  Site Map  |  Privacy Statement   |  Contact Us

©2014 Colquhoun Audio Laboratories Limited
All Rights Reserved.