Previous Thread
Next Thread
Print Thread
Rate Thread
Page 2 of 2 1 2
Re: Is this bad for my amp?
Thasp #151989 11/25/06 04:28 AM
Joined: Jun 2003
Posts: 6,833
W
Wid Offline
axiomite
Offline
axiomite
W
Joined: Jun 2003
Posts: 6,833
Quote:

I don't get 86 at 1 watt 1 meter




Just being curious. When it is stated 86dB/W/m (2.8V) does this mean it is tested @ 2.8 V ? If this is the case then wouldn't it require a doubling of watts @ 4 ohm to produce the 86 db rating and not 1 watt.


Rick


"A fear of weapons is a sign of retarded sexual and emotional maturity." Sigmund Freud

Re: Is this bad for my amp?
Wid #151990 11/25/06 05:24 AM
Joined: May 2002
Posts: 10,654
shareholder in the making
Offline
shareholder in the making
Joined: May 2002
Posts: 10,654
Rick, Thasp hasn't checked back in and didn't give full details of how he measured and calculated, but yes, what you're suggesting is correct. The applicable form of Ohm's Law is that power equals the square root of (Vsquared/resistance), so the standard measure is 2.83V input into 8ohms, which is equivalent to 1 watt. If 2.83V was instead input into 4ohms, the power would be 2 watts rather than 1 watt. To actually get a 4ohm number for 1 watt the input would be 2.0V rather than 2.83V(or the result would be adjusted down by 3dB to compensate for the lower impedance).

Another point is that the basic sensitivity measure is supposed to be taken under anechoic conditions, and as we discussed with Gena quite a while ago, measured in room at normal listening distances the reverberent sound field can be as strong or stronger than the direct field(so the 6dB loss per doubling of distance isn't the complete picture and less power is required than that measure would imply).


-----------------------------------

Enjoy the music, not the equipment.


Re: Is this bad for my amp?
JohnK #151991 11/25/06 05:34 AM
Joined: Mar 2004
Posts: 340
Thasp Offline OP
devotee
OP Offline
devotee
Joined: Mar 2004
Posts: 340
I measured the impedance myself, this is quite easy with a multimeter. I did not measure sensitivity myself, someone else did. I didn't ask him to but he was curious, since he also noticed the amp getting hot. He plays live music and has an SPL meter in his bag with a relatively nice mic compared to the radioshack crap, but I don't know how he got exactly 1 watt out of the amp.. or maybe he didn't. It happened after he noticed it was hot when he walked past the amp.

I still see a jaw drop to everyone I demo these to.

Last edited by Thasp; 11/25/06 05:35 AM.
Re: Is this bad for my amp?
Thasp #151992 11/25/06 06:34 AM
Joined: Sep 2002
Posts: 1,488
connoisseur
Offline
connoisseur
Joined: Sep 2002
Posts: 1,488
heatsinks will get much hotter than the outside of the amp, Depending on the design you can touch the heatsinks, my old NAD was like this, if you stuck your finger up the bottom vent and touched the heatsink directly after cranking it you would be greeted by a little too much heat.

The sound that keeps playing when you unplug the amp means that first of all you have got a decent amount of filter capacitance, and that you also dont have a speaker protection relay that will usually come on when you do something like unplug the amp. This is perfectly normal for amps without a relay.

Also keep in mind that you cannot measure impedance with a multimeter by just sticking the probes on the speaker terminals. Speaker Impedance is the average of the different resistance at different frequencies.

Last edited by Haoleb; 11/25/06 06:36 AM.
Re: Is this bad for my amp?
Haoleb #151993 11/25/06 07:10 AM
Joined: Mar 2005
Posts: 7,463
Likes: 1
axiomite
Offline
axiomite
Joined: Mar 2005
Posts: 7,463
Likes: 1
Quote:

if you stuck your finger up the bottom vent and touched the heatsink directly after cranking it




Brandon, you're making this way too easy. . .


***********
"Nothin' up my sleeve. . ." --Bullwinkle J. Moose
Re: Is this bad for my amp?
JohnK #151994 11/25/06 11:34 AM
Joined: Jun 2003
Posts: 6,833
W
Wid Offline
axiomite
Offline
axiomite
W
Joined: Jun 2003
Posts: 6,833

Thanks John.


Rick


"A fear of weapons is a sign of retarded sexual and emotional maturity." Sigmund Freud

Re: Is this bad for my amp?
Thasp #151995 11/25/06 01:06 PM
Joined: May 2002
Posts: 1,177
connoisseur
Offline
connoisseur
Joined: May 2002
Posts: 1,177
Quote:

I can tape the corners of the fan to the two back corners of the amp and it'll blow cool air through the fins.




Someone with more smarts than me can chime in, but I thought that you were supposed to be drawing the hot air out. Not trying to blow air in.


Shawn

Epic 80/600 + M3's + M3 Algonquins + M2 Computer + EP125
I think I'm developing an addiction.
Re: Is this bad for my amp?
real80sman #151996 11/26/06 06:58 AM
Joined: Mar 2004
Posts: 340
Thasp Offline OP
devotee
OP Offline
devotee
Joined: Mar 2004
Posts: 340
PC cooling designs always have the fan pointing down to bring cool air down to the heatsink. VGA coolers, active chipset coolers, hard drive coolers(if your PC has these, doubt it does unless you put them in yourself).

Re: Is this bad for my amp?
Thasp #151997 11/26/06 08:45 AM
Joined: Dec 2003
Posts: 3,602
B
connoisseur
Offline
connoisseur
B
Joined: Dec 2003
Posts: 3,602
And amps and rackmount equipment take hot air out with filter elements on the intakes.

Slit throat, slit spine : same-same.

Bren R.

Re: Is this bad for my amp?
real80sman #151998 11/26/06 03:00 PM
Joined: Aug 2004
Posts: 6,379
Likes: 7
axiomite
Offline
axiomite
Joined: Aug 2004
Posts: 6,379
Likes: 7
>>Someone with more smarts than me can chime in, but I thought that you were supposed to be drawing the hot air out. Not trying to blow air in

This isn't a cast-in-stone rule... it's just that you normally want the fan to be assisting natural convection, not fighting it. As others have said, though, sometimes there are good arguments for doing something different.


M60ti, VP180, QS8, M2ti, EP500, PC-Plus 20-39
M5HP, M40ti, Sierra-1
LFR1100 active, ADA1500-4 and -8
Page 2 of 2 1 2

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,940
Posts442,457
Members15,616
Most Online2,082
Jan 22nd, 2020
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,840
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 402 guests, and 3 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4