Re: What to do with EP600 for Audyssey calibration?
|
Joined: Jan 2007
Posts: 10,490 Likes: 116
shareholder in the making
|
shareholder in the making
Joined: Jan 2007
Posts: 10,490 Likes: 116 |
The timing is frequency-dependent. You can do a time domain analysis and use the second moment about the mean. Personally, I skipped all that and did it by ear giving me ample time to consume my beer .
|
|
|
Re: What to do with EP600 for Audyssey calibration?
|
Joined: Jul 2004
Posts: 4,444 Likes: 16
connoisseur
|
connoisseur
Joined: Jul 2004
Posts: 4,444 Likes: 16 |
Terz,
I have always added six feet to my sub's actual distance, but I'll give three feet a try as Jake suggests (he's the sub guru). I originally recomended that you leave it as is because if you go making several changes at once, you'll end up chasing your tale. Make small changes, and only one at a time.
I've been playing around with the manual EQ set up and think I have it set up about as good as it can be, but I've been tweaking things slowly, and keeping track of what the sonic differences have been.
|
|
|
Re: What to do with EP600 for Audyssey calibration?
|
Joined: Jul 2006
Posts: 12,077 Likes: 7
Founder, Axiom Upgrade Club shareholder in the making
|
Founder, Axiom Upgrade Club shareholder in the making
Joined: Jul 2006
Posts: 12,077 Likes: 7 |
The kind of processing power required is the type in your PC or notebook, which you are not going to find in a receiver or dedicated equalizer anytime soon. If this is all that's holding them back, I don't see why it hasn't made it into a receiver yet, especially at the higher end. And you'd think they'd make dedicated hardware specifically for that task. I admit I know nothing, but to me, it seems like it has to be that the software isn't mature enough, not the hardware. Otherwise, I don't see how we couldn't see very advanced room correction within 5 years. Assuming the software needs the fastest processor there is currently, there's no way it couldn't be cheap enough to implement in that timeframe.
|
|
|
Re: What to do with EP600 for Audyssey calibration?
|
Joined: Oct 2005
Posts: 853
aficionado
|
aficionado
Joined: Oct 2005
Posts: 853 |
Correcting room acoustical issues electronically is a very complex undertaking requiring sophisticated software and dedicated fast hardware . Doing proper measurements alone takes a massive amount of processing time because it involves running iterations of sweeps and adjustments. More calculations are required for the bass frequencies because of the nature of long wavelengths in the room.
The few programs that come close to doing it properly are the Audessey PRO which is very expensive and can be connected to a PC and takes a while to run; or Room EW which is free software used with a notebook. All the Audessey eq programs liscenced for receivers are ineffectual watered down versions with simplified algorythms designed to run just a few iterations, make computations then recommendations made on simplyfing assumptions. Those simplified rules rarely correspond with your unique room acoustical requirements.
That's why I always say that based on current technology in receivers, there is no way such a program can do as good a job as someone with a RS metre and a measurement tape. Perhaps one day they will as the technology gets better and the cost of processing falls but don't hold your breath anytime soon.
John
|
|
|
Re: What to do with EP600 for Audyssey calibration?
|
Joined: Dec 2007
Posts: 17
frequent flier
|
frequent flier
Joined: Dec 2007
Posts: 17 |
Nuke, if you're using the crossover in the receiver, either set manually or by Odyssey, there's still no good reason in my view to also insert the internal sub variable low pass filter. Set it on bypass. Sorry to bother. What is a bypass switch? My sub doesn't have the bypass switch. It only have two knobs, the gain control and crossover freq. control. Right now I have my sub gain knob set at 12 o'clock and sub crossover control know all the way up to 130Hz. Sub crossover control know all the way is the same as the bypass switch ON.
|
|
|
Re: What to do with EP600 for Audyssey calibration?
|
Joined: Aug 2007
Posts: 3,488 Likes: 9
connoisseur
|
connoisseur
Joined: Aug 2007
Posts: 3,488 Likes: 9 |
It is the crossover switch. It's highest setting is "bypass".
See Mojo's signature
|
|
|
Re: What to do with EP600 for Audyssey calibration?
|
Joined: Dec 2007
Posts: 17
frequent flier
|
frequent flier
Joined: Dec 2007
Posts: 17 |
Thanks Eflardeau. Got it. This I will leave my crossover to the highest setting.
|
|
|
Forums16
Topics24,943
Posts442,465
Members15,617
|
Most Online2,082 Jan 22nd, 2020
|
|
0 members (),
762
guests, and
4
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|