Previous Thread
Next Thread
Print Thread
Rate Thread
Page 6 of 10 1 2 4 5 6 7 8 9 10
Re: Speaker wire with new Axioms
jakewash #212914 06/24/08 09:00 PM
Joined: May 2003
Posts: 18,044
shareholder in the making
Offline
shareholder in the making
Joined: May 2003
Posts: 18,044
I use RG7.3.


I am the Doctor, and THIS... is my SPOON!
Re: Speaker wire with new Axioms
Ken.C #212918 06/24/08 09:11 PM
Joined: Mar 2005
Posts: 7,463
Likes: 1
axiomite
Offline
axiomite
Joined: Mar 2005
Posts: 7,463
Likes: 1
I stick my finger in the sub and my toe in the receiver. So there.


***********
"Nothin' up my sleeve. . ." --Bullwinkle J. Moose
Re: Speaker wire with new Axioms
St_PatGuy #212920 06/24/08 09:12 PM
Joined: May 2003
Posts: 18,044
shareholder in the making
Offline
shareholder in the making
Joined: May 2003
Posts: 18,044
That explains so much.


I am the Doctor, and THIS... is my SPOON!
Re: Speaker wire with new Axioms
Ken.C #212922 06/24/08 09:40 PM
Joined: Feb 2006
Posts: 6,471
axiomite
Offline
axiomite
Joined: Feb 2006
Posts: 6,471
That's how I perform ECT!

I have found that the best CD for that is "Thunder and Lightning"


Bears, beets, Battlestar Galactica.
Re: Speaker wire with new Axioms
terzaghi #212932 06/25/08 02:04 AM
Joined: May 2002
Posts: 10,654
shareholder in the making
Offline
shareholder in the making
Joined: May 2002
Posts: 10,654
And David, the second one has a "fancy connector". As I said in my previous reply, the RG59 cable is fine.


-----------------------------------

Enjoy the music, not the equipment.


Re: Speaker wire with new Axioms
jakewash #212935 06/25/08 02:19 AM
Joined: Sep 2002
Posts: 1,488
connoisseur
Offline
connoisseur
Joined: Sep 2002
Posts: 1,488
Yup they will both work just fine. Personally I would go with the RG6 but it really doesnt matter. The big difference between the two can be seen when being used for CATV. You definetly dont want to use RG59 for that purpose these days as it will degrade signal quality.

Re: Speaker wire with new Axioms
terzaghi #212952 06/25/08 03:15 PM
Joined: Jun 2008
Posts: 135
veteran
OP Offline
veteran
Joined: Jun 2008
Posts: 135
 Originally Posted By: terzaghi
I ran audessey with my m80'sd and wasn't terribly happy with the results. I changed the setting on my sub and re-ran it.... I had adjusted some of the channels after the audessey set up (fine tuned things with my SPl meter) and for some reason audessey just kept reverting to the old settings.

Acouple of weeks ago I did a hard reset and manually adjusted everything without ever running audessey. So far I like things much better without it...


terzaghi, what did you do to do a hard reset on your avr? My Axioms should arrive within the next few hours and if there is a chance that the avr may revert back to the "old" settings I may want to do a hard reset also.


"Real Gun Control Is Hitting What You Aim At" - can't remember
Re: Speaker wire with new Axioms
edmondwolfman #212954 06/25/08 03:35 PM
Joined: Apr 2007
Posts: 4,877
connoisseur
Offline
connoisseur
Joined: Apr 2007
Posts: 4,877
from the denon manual:

microprocessor reset (master power off, hold down both the DSP and the Standard button, master power on, wait for three flashes, release buttons)

standard reset (master power off, hold down both the 'up arrow' button and the 'down arrow' button, master power on, wait for the flashing, release buttons).

I did a standard reset, it resets all of your channel levels, any audessey results, video settings/ input names and assignments, ect.- basically puts it back to its factory setting (without downgrading any firmware updates that you may have installed.)



not sure if that is really necessary if you plan on running audessey. I would do a reset first if for some reason you decide to do everything manually after you have already ran audessey.



-David
Re: Speaker wire with new Axioms
terzaghi #212957 06/25/08 03:42 PM
Joined: Jun 2008
Posts: 135
veteran
OP Offline
veteran
Joined: Jun 2008
Posts: 135
 Originally Posted By: terzaghi
from the denon manual:

microprocessor reset (master power off, hold down both the DSP and the Standard button, master power on, wait for three flashes, release buttons)

standard reset (master power off, hold down both the 'up arrow' button and the 'down arrow' button, master power on, wait for the flashing, release buttons).

I did a standard reset, it resets all of your channel levels, any audessey results, video settings/ input names and assignments, ect.- basically puts it back to its factory setting (without downgrading any firmware updates that you may have installed.)



not sure if that is really necessary if you plan on running audessey. I would do a reset first if for some reason you decide to do everything manually after you have already ran audessey.


Thanks terzaghi for the fast response. I'm standing with my nose against the window wondering "where oh where is that FEDEX truck"


"Real Gun Control Is Hitting What You Aim At" - can't remember
Re: Speaker wire with new Axioms
edmondwolfman #212958 06/25/08 03:51 PM
Joined: Apr 2007
Posts: 4,877
connoisseur
Offline
connoisseur
Joined: Apr 2007
Posts: 4,877
yeah, I went and picked up my speakers from DHL on my lunch hour... took two trips to fit them all in my jeep, I just couldnt squeeze the ep500 in with everything else


-David
Page 6 of 10 1 2 4 5 6 7 8 9 10

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,940
Posts442,457
Members15,616
Most Online2,082
Jan 22nd, 2020
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,840
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 386 guests, and 4 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4