Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
Audyssey crossover settings
#328306 11/13/10 03:41 AM
Joined: Apr 2006
Posts: 122
veteran
OP Offline
veteran
Joined: Apr 2006
Posts: 122
I've just run Audyssey XT32 for the first time in my new Denon 4311 receiver. I've never run Audyssey before so this was a new experience. I haven't had much time to listen so I can't offer a review but I do have some questions regarding the crossovers and speaker settings Audyssey and my receiver chose.

My M60s were set to large (which implies a measured -3db point below 40 Hz). My M2 heights were set to small at 80 Hz crossover. My VP150 center was set to small at 110 Hz. My QS8 surrounds were set to small at 120 Hz.

Do these sound right? What have others experienced when running Audyssey?

I ended up setting my M60s to small and bumped the crossover to 60 Hz - although I might play around with setting them at 40 Hz.

I was a bit surprised by the QS8 surrounds. Does 120 Hz sound right? My concern is whether my EP500 can fill in the full range below 120 Hz. Will the EP500 fill in the upper end of the bass below 120 Hz - say from 80 Hz to 120 Hz? This also applies to the VP150 which is set for 110 Hz.

Thoughts?

Bryan

Re: Audyssey crossover settings
icehawk21 #328307 11/13/10 03:55 AM
Joined: May 2002
Posts: 10,654
shareholder in the making
Offline
shareholder in the making
Joined: May 2002
Posts: 10,654
Bryan, the surround crossover measurement is a notch higher than typical, but apparently in your mounting location that's their bass capability. Although the M60 measurement, as you say, apparently showed good enough response at 40Hz for the "large" setting, that doesn't mean that it's the best overall result. As Dr. Kyriakakis suggests, the mains should manually be set "small", with perhaps an 80Hz crossover, so that the sub can handle more of what it does best.


-----------------------------------

Enjoy the music, not the equipment.


Re: Audyssey crossover settings
icehawk21 #328308 11/13/10 04:04 AM
Joined: Jan 2004
Posts: 13,840
Likes: 13
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,840
Likes: 13
Assuming you took your measurement locations correctly from each location, in a dead quiet room, with nothing in the way of the mic to provide reflections, and none of the measurments were taken "outside" the boundaries of the speaker, I would say they don't seem unreasonable.

You were correct in changing the m60's to small, and bumping up the crossover, you might try 80hz even. I have used 60 and 80hz for my m80's and there is not a huge difference.

I think the first time I ran Audyssey, my Qs8's were set to 120hz by Denon (not Audyssey smile ) which is ok and has a lot to do with your room and how you measured. However, after rerunning the sweeps from more refined locations to create a "bubble" around the seating area, they are now set to 90hz, which is fine.

110hz does not sound out of line for the 150, but again I am not familiar with your room, and your measurement locations, so that may change as you become more familiar with the best practices of using Audyssey.

Whatever you do, don't lower a crossover below that which was set by your receiver. It is ok to bump it up, but if you go down you will be losing the room calibration from Audyssey above that point.


M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Re: Audyssey crossover settings
SirQuack #328314 11/13/10 04:36 AM
Joined: Dec 2006
Posts: 3,569
connoisseur
Offline
connoisseur
Joined: Dec 2006
Posts: 3,569
Originally Posted By: icehawk21

I was a bit surprised by the QS8 surrounds. Does 120 Hz sound right? My concern is whether my EP500 can fill in the full range below 120 Hz. Will the EP500 fill in the upper end of the bass below 120 Hz - say from 80 Hz to 120 Hz? This also applies to the VP150 which is set for 110 Hz


I would try repositioning your speakers trying to take advantage of boundary reinforcement from walls corners with your QS8s and the front wall or cabinet walls for your VP150. This might help your Denon detect them as going lower. Also trying different microphone locations as suggested might also help.

If that doesn’t get you lower numbers I would at least try lowering the crossover from 120 to 110 or even 100 for your QS8s and to 100 for your VP150. At least that way the speaker will try to play a little more of what would otherwise be a large dip in SPL above 100Hz where the EP500 drops off like a rock. The tradeoff is that there is no Audessey curve calculated below where the Denon set the speaker. Given a choice of no Audessey curve or a deep drop in SPL I would do without Audessey over that small frequency range.


3M80 2M22 6QS8 2M2 1EP500 Sony BDP-S590 Panny-7000 Onkyo-3007 Carada-134 Xbox Buttkicker AS-EQ1
Re: Audyssey crossover settings
grunt #328315 11/13/10 04:41 AM
Joined: Jun 2003
Posts: 6,833
W
Wid Offline
axiomite
Offline
axiomite
W
Joined: Jun 2003
Posts: 6,833

Or go without Audessey entirely. I tried it and did not like the results. I went and did all the settings manually.


Rick


"A fear of weapons is a sign of retarded sexual and emotional maturity." Sigmund Freud

Re: Audyssey crossover settings
Wid #328316 11/13/10 04:42 AM
Joined: Dec 2006
Posts: 3,569
connoisseur
Offline
connoisseur
Joined: Dec 2006
Posts: 3,569
Originally Posted By: wid

Or go without Audessey entirely. I tried it and did not like the results. I went and did all the settings manually.


I thought about saying that but didn’t want to open that can of worms here again. wink


3M80 2M22 6QS8 2M2 1EP500 Sony BDP-S590 Panny-7000 Onkyo-3007 Carada-134 Xbox Buttkicker AS-EQ1
Re: Audyssey crossover settings
icehawk21 #328318 11/13/10 05:00 AM
Joined: May 2002
Posts: 10,654
shareholder in the making
Offline
shareholder in the making
Joined: May 2002
Posts: 10,654
Bryan, yes you might try rearranging the mounting positions for greater bass support, if feasible. If not, your EP500, with the low pass filter set to the 150Hz max(my earlier model has a 100Hz brick wall filter)can cover those frequencies up to 120Hz, as required by the receiver crossover.


-----------------------------------

Enjoy the music, not the equipment.


Re: Audyssey crossover settings
JohnK #328321 11/13/10 05:20 AM
Joined: Dec 2006
Posts: 3,569
connoisseur
Offline
connoisseur
Joined: Dec 2006
Posts: 3,569
Thanks for mentioning that John. I forgot the redesigned it. I wonder why they still only show a graph up to 100Hz?


3M80 2M22 6QS8 2M2 1EP500 Sony BDP-S590 Panny-7000 Onkyo-3007 Carada-134 Xbox Buttkicker AS-EQ1
Re: Audyssey crossover settings
grunt #328331 11/13/10 06:15 AM
Joined: Dec 2003
Posts: 10,420
J
shareholder in the making
Offline
shareholder in the making
J
Joined: Dec 2003
Posts: 10,420
Bryan, I know your room and that QS8 setting is not unreasonable. I am a little surprised at the VP150 but again it is not unreasonable for your large open room. I suspect a little aiming of the VP150 might be in order, higher or lower and you might be able to get the frequency to drop a little not that you should be concerened, the VP180 will be the one taking it's place shortly.


Jason
M80 v2
VP160 v3
QS8 v2
PB13 Ultra
Denon 3808
Samsung 85" Q70
Re: Audyssey crossover settings
jakewash #328345 11/13/10 01:34 PM
Joined: Dec 2008
Posts: 6,928
axiomite
Offline
axiomite
Joined: Dec 2008
Posts: 6,928
Audyssey set my QS8's at 150hz!


Half of communication is listening. You can't listen with your mouth.
Page 1 of 2 1 2

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,940
Posts442,457
Members15,616
Most Online2,082
Jan 22nd, 2020
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,840
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 136 guests, and 1 robot.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4