Previous Thread
Next Thread
Print Thread
Rate Thread
Page 2 of 2 1 2
Re: Upgrade AudioBytes Speakers to M2?
jmone #392731 05/05/13 11:42 AM
Joined: Jan 2006
Posts: 353
jmone Offline OP
devotee
OP Offline
devotee
Joined: Jan 2006
Posts: 353
So - any suggestions on a "small" amp/receiver to drive a 2.1 speaker system to fill a small room?

Last edited by jmone; 05/05/13 11:42 AM.

HT:M80,VP150,QS8,EP500 Outside:4xM3 Office:AudioBytes, Rumpus: M60,VP150,M22 Portable:2 x Airs
Re: Upgrade AudioBytes Speakers to M2?
jmone #392747 05/06/13 02:53 AM
Joined: May 2002
Posts: 10,654
shareholder in the making
Offline
shareholder in the making
Joined: May 2002
Posts: 10,654
The use of "fill" indicates that you may want a much higher sound level than is used while at the computer. It also may help to explain why three Audiobyte drivers have gone down. What did Axiom suggest was the problem(and were they mid-woofers, tweeters or both?)? You may have simply been playing them at a level well beyond what the amplifier(intended for typical computer speaker use)could handle without clipping and damaging the drivers.

If the lower sound level which is safe isn't adequate for all your uses, then yes, a bigger and more powerful setup would be needed. I'd strongly suggest a multi-channel HT receiver even if you're only considering 2.1 use now. The bass management to cross over the sub and speakers(which almost no 2-channel receivers have)is a substantial plus and the economies in producing these units in quantity result in getting more for a similar amount of money compared to stereo units.

I've visited Sydney, but know almost nothing about the Australian audio equipment market. I took a look at a Sydney dealer here for the sort of unit I might suggest, but was appalled at the price, which at about $460 USD was about twice what would be paid in the U.S. Possibly shipping and other charges involved in your buying from the U.S. would almost wipe out any savings. In any case, I'd suggest an Onkyo or Denon 5.1 model in the 80 watt or above class, or if you get just a stereo unit, the HK-3390 would be suitable.


-----------------------------------

Enjoy the music, not the equipment.


Re: Upgrade AudioBytes Speakers to M2?
jmone #392759 05/06/13 06:42 AM
Joined: Jan 2006
Posts: 353
jmone Offline OP
devotee
OP Offline
devotee
Joined: Jan 2006
Posts: 353
Thanks John. I'm comfortable with the flexibility and power of the AVR approach for the reasons suggested but just don't like the physical presence for a Study. And yes we pay inflated prices down under but I could just get a second hand AVR (without any fancy Video Processing as these older HDMI units are now cheap as chips).

I've had lots of toing and froing with Axiom over this system trying to work out why I've blown 3 x "mid woofers" on the Sat and never the Tweeters or the drivers in the Sub. Axiom suggested that the system should be able to play at full vol from the included Audiobyte amp and that it must be distortion in the input but.....now I just play at lower sound pressure levels. (note: I'm also on my second amp - the first one had a bad hum to it. I've also removed the flying remote as this introduced a hum as well a certain positions.... + I replaced all the supplied cables with shielded / ferrite baluns and they made a big improvement removing hum) and so far so good. I'm just nervous of "Cranking" it up, hence the Q on the upgrade path. Given the full AVR alternative I may just enjoy what I have yet!


HT:M80,VP150,QS8,EP500 Outside:4xM3 Office:AudioBytes, Rumpus: M60,VP150,M22 Portable:2 x Airs
Re: Upgrade AudioBytes Speakers to M2?
jmone #392760 05/06/13 07:11 AM
Joined: Jan 2006
Posts: 353
jmone Offline OP
devotee
OP Offline
devotee
Joined: Jan 2006
Posts: 353
Another thought - on my PC I can also do full Bass Mgt in SW (I use JRiver Media Center) so a small 2ch amp + active sub would also be fine....


HT:M80,VP150,QS8,EP500 Outside:4xM3 Office:AudioBytes, Rumpus: M60,VP150,M22 Portable:2 x Airs
Re: Upgrade AudioBytes Speakers to M2?
jmone #392940 05/09/13 10:55 AM
Joined: Jan 2006
Posts: 353
jmone Offline OP
devotee
OP Offline
devotee
Joined: Jan 2006
Posts: 353
I've ordered another set of Algonquin for the 2.0 part (as I can redeploy them outside if needed). Say I drive the new setup with an AVR or dedicated mono blocks, can I use the AudioBytes Sub as the 0.1 with them or is the lack of cross over going to be an issue?


HT:M80,VP150,QS8,EP500 Outside:4xM3 Office:AudioBytes, Rumpus: M60,VP150,M22 Portable:2 x Airs
Re: Upgrade AudioBytes Speakers to M2?
jmone #392941 05/09/13 11:23 AM
Joined: May 2003
Posts: 18,044
shareholder in the making
Offline
shareholder in the making
Joined: May 2003
Posts: 18,044
You probably won't be able to use the sub with them, either. Sorry!


I am the Doctor, and THIS... is my SPOON!
Re: Upgrade AudioBytes Speakers to M2?
jmone #393238 05/18/13 03:37 AM
Joined: Oct 2007
Posts: 395
devotee
Offline
devotee
Joined: Oct 2007
Posts: 395
On the plus side M3s do sound excellent without a sub. I used M2s for a while as computer speakers and even with a sub found them lacking (though they were very clear and precise, just "lacking" that certain je ne sais quoi). I now use M22s for the computer with a sub and love them. My M3s serve as a standalone 2.0 system in the bedroom and I love them as well.


M80s/VP160/QS8s/EP350; M22s; M3s.
Page 2 of 2 1 2

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,940
Posts442,457
Members15,616
Most Online2,082
Jan 22nd, 2020
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,840
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 386 guests, and 4 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4