Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 2 1 2
AV receiver vs. stereo Amp?
#424579 03/29/17 02:15 AM
Joined: Jul 2015
Posts: 110
Likes: 3
R
Rock Offline OP
veteran
OP Offline
veteran
R
Joined: Jul 2015
Posts: 110
Likes: 3
Hi guys,

Many suggested me to test AV receiver vs. stereo Amp for below reasons:
1. My NAD 3556BEE only has 80W power, no Sub pre-out. So I have to run full range on my M22s even though my EP500 is very powerful.
2. AV receiver could create/restore more realistic music for better experience.

I did a test today but not satisfying with the results.

Got a second hand Denon AVR 1802/882 and run M22s and sub. However the receiver couldn't generate the same level of detailed,warm, controlled bright sound especially on the high range. The sound is not bad in general and at least better than my expectation. But certainly not as good as the stereo amp. I set the receiver with pure stereo, tone defeat mode. Use the same CD source.

What is your experience and suggestion? Maybe I should use a more expensive receiver? I am thinking to connect receiver front pre-out to NAD line-in to see if there will be any difference.

Thanks.

Re: AV receiver vs. stereo Amp?
Rock #424584 03/29/17 03:32 AM
Joined: Aug 2004
Posts: 6,379
Likes: 7
axiomite
Offline
axiomite
Joined: Aug 2004
Posts: 6,379
Likes: 7
Whoa, welcome to the slippery slope smile

Dumb questions to start with:

1. IIRC there are some modes ("Pure Direct" comes to mind) where not only tone controls are disabled but also the DSP processing which generates low-pass subwoofer output and high-pass mains output. Are you fairly sure you were not running one of those ?

2. When you say "... bright sound especially on the high range..." does "high range" refer to "loud" or something else ?


M60ti, VP180, QS8, M2ti, EP500, PC-Plus 20-39
M5HP, M40ti, Sierra-1
LFR1100 active, ADA1500-4 and -8
Re: AV receiver vs. stereo Amp?
Rock #424586 03/29/17 12:24 PM
Joined: May 2014
Posts: 1,170
Likes: 6
M
MMM Offline
connoisseur
Offline
connoisseur
M
Joined: May 2014
Posts: 1,170
Likes: 6
I have a different take on it. Your NAD will have a better amplifier inside of it. With a torrodial power transformer. I am going to guess that it is some sort of digital amplifier inside but likely has some analog domain inside it as well.

The Denon is pure digital. So you are loosing out on some of the warmth that you are use to with the NAD. I found from my own experience that every receiver that i have bought since 2005 have sounded empty. All except the last unit, the Anthem. That however cost far more than I generally paid in the past.

I don't know if the digital domain gets the same sound when it is done on the cheep.


Anthem: AVM60, Fosi DAC-Q5
Axiom: ADA1500, LFR1100 Actiive, QS8, EP500, M3, M3comp, M5
Re: AV receiver vs. stereo Amp?
Rock #424587 03/29/17 01:10 PM
Joined: Jan 2002
Posts: 1,459
Likes: 6
connoisseur
Online Content
connoisseur
Joined: Jan 2002
Posts: 1,459
Likes: 6
Perhaps you can describe what you are trying to achieve with this testing? The NAD is a solid unit, albeit without all the bells and whistles. I used a 7240 for years driving Axiom AX3's and later M80's with an EP350 to great joy.

If your trying to get the M22's and EP500 to work within the frequency ranges, I originally connected my 7240 to the High Pass inputs on the EP350 and then ran cables to the M80's. The sub acts like an AVR would by setting the limits on frequency passed to the downstream speakers.

This required extra cables, but worked well. Not sure if the newer subs still offer this capability.

Re: AV receiver vs. stereo Amp?
bridgman #424589 03/29/17 01:59 PM
Joined: Jul 2015
Posts: 110
Likes: 3
R
Rock Offline OP
veteran
OP Offline
veteran
R
Joined: Jul 2015
Posts: 110
Likes: 3
I would test it again to see if all DSP is disabled.

High range to me means high frequencies, not loud.

Still wondering if a more expensive receiver would make more difference.

Currently considering to get a used Pioneer Elite Receiver Model VSX-21TXH 400 W for another try.

Re: AV receiver vs. stereo Amp?
MMM #424590 03/29/17 02:01 PM
Joined: Jul 2015
Posts: 110
Likes: 3
R
Rock Offline OP
veteran
OP Offline
veteran
R
Joined: Jul 2015
Posts: 110
Likes: 3
Good point. I could feel the difference between pure digital and hybrid digital and analog.

Re: AV receiver vs. stereo Amp?
BBIBH #424591 03/29/17 02:03 PM
Joined: Jul 2015
Posts: 110
Likes: 3
R
Rock Offline OP
veteran
OP Offline
veteran
R
Joined: Jul 2015
Posts: 110
Likes: 3
EP500 doesn't have a high pass out for downstream speakers. So I may have to use AVR or get another AMP to separate the frequencies.

Re: AV receiver vs. stereo Amp?
Rock #424592 03/29/17 03:15 PM
Joined: Oct 2012
Posts: 2,021
Likes: 1
B
connoisseur
Offline
connoisseur
B
Joined: Oct 2012
Posts: 2,021
Likes: 1
Maybe Ian or another member with a EP500 can confirm....you should be able to twist the cable ends together at the EP500 and not need an "output".
Run your left and your right cable to the sub, join the ends of these cables with the ends of the cable needed to reach your speakers by twisting the ends together, insert and tighten. Once for the left, once for the right.
Set your crossover using the subs crossover adjustment/knob.
Remove any extra equipment, try with just the Nad and a player of choice as per the recommendations given.

Last edited by brwsaw; 03/29/17 03:16 PM.


Re: AV receiver vs. stereo Amp?
brwsaw #424593 03/29/17 03:49 PM
Joined: Jul 2015
Posts: 110
Likes: 3
R
Rock Offline OP
veteran
OP Offline
veteran
R
Joined: Jul 2015
Posts: 110
Likes: 3
I doubt that crossover of the sub would do anything to filter the low frequency when just simply twist the two cables. The reason is that the signal you pass to the speakers is exactly the same you get from the amp since they don't pass through the sub at all.

I maybe wrong:)

Re: AV receiver vs. stereo Amp?
Rock #424594 03/29/17 04:18 PM
Joined: Feb 2009
Posts: 1,181
Likes: 1
connoisseur
Offline
connoisseur
Joined: Feb 2009
Posts: 1,181
Likes: 1
Hi guys, this was discussed recently over in this thread .

Just scroll down to JohnK's and 2x6Spds posts which have great info on bass management and what signals go where.


Dan
On-Wall M5HP LCR, QS8 & EP500 in 7.1
Page 1 of 2 1 2

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,940
Posts442,457
Members15,616
Most Online2,082
Jan 22nd, 2020
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,840
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 558 guests, and 3 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4