Get Free, Friendly, Expert Advice
Call 1-888-352-9466 or email

Designed and Manufactured in Canada Since 1980


AxiomAudio Blog

Insider’s Sneak Peek: AxiomAeris

Axiom’s New Computer Speakers

Blind Listening Tests

Wall'O'Fame
Solarrdadd's 7.1 Apartment HT!
A promise is A promise... Axiom's second home
Who's Online
4 registered (CV, newf, Boltron, Serenity_Now), 49 Guests and 6 Spiders online.
Key: Admin, Global Mod, Mod
Financing
Forum Stats
13365 Members
11 Forums
23109 Topics
408632 Posts

Max Online: 378 @ 02/24/13 04:33 PM
Top Posters
Ken.C 17869
pmbuko 16328
SirQuack 13356
CV 11413
MarkSJohnson 11082
Meanwhile On Facebook

Any roadies / concert lovers out there think this is as cool as I do?

󾓶Ay, caramba! Our 'sneak peek' announcement in this morning's newsletter genera...

󾔸 Testing various operating systems with our new High Power Computer Speakers t...

Kick it up for Tone!

Topic Options
Rate This Topic
#85613 - 03/16/05 07:00 PM Bi-Wirable and other novice questions....
GuyintheTV Offline
regular

Registered: 03/16/05
Posts: 6
Loc: Washington State
I was wondering about the Bi-wirable and Bi-ampable terms for one. How do you hook these speakers up to a typical receiver? IE-A Pioneer Elite receiver equipped with only one speaker input for both R and L mains. Do you split the wire up when hooking it up to the speaker? Also, if I were to purchase the M80ti's before I bought a new receiver, and hooked them up to an entry level receiver (Sherwood) with an 8ohm rating would it damage the speakers in any way? Has anyone had any good/bad experiences with Pioneer Elite units? Thanks in advance for any help you all can give me. Afterall, I'm here to learn!!

-GuyintheTV
_________________________
Yes I'm a novelist, I've got an obscenely prodigious vocabulary, and yes I flaunt it unabashedly.

Top
#85614 - 03/16/05 07:33 PM Re: Bi-Wirable and other novice questions....
bridgman Offline
axiomite

Registered: 08/25/04
Posts: 5529
Loc: Bowmanville, Ontario, Canada
For biwiring you would run two pairs of speaker wires for each speaker rather than the single pair per speaker normally used. At the receiver end, both "red/plus" wires would go to the "red" jack and both "black/minus" wires would go to the "black" jack. At the speaker end you would remove the jumpers between the two pairs of jacks, hook red/black from one pair to the mid/tweeter jacks and red/black from the other pair to the woofer jacks.

I don't think many people on this board feel it is worth the effort, but a few people swear by it.

Bi-amping is the same idea but you need two amplifiers driven with the same signal (ideally through an electronic crossover. At the speaker end the wiring would be the same as for bi-wiring, but at the receiver/amp end the two pairs would go to different amplifier outputs.

Bi-amping is felt to add some real value if you have a good electronic crossover but is only really seen in large professional sound systems. One of the most obvious benefits is the ability to drive the woofer amp into clipping without frying your tweeters, so you don't have to worry so much about cranking the volume a bit too high for the amp's capabilities.

Top



Moderator:  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Home  |  Corporate Info  |  Products  |  Message Board  |  FAQs  |  Warranty  |  Site Map  |  Privacy Statement   |  Contact Us

©2015 Colquhoun Audio Laboratories Limited
All Rights Reserved.