Previous Thread
Next Thread
Print Thread
Rate Thread
QS8 Roll-off Frequency
#415472 11/13/15 09:02 PM
Joined: Dec 2013
Posts: 20
M
mrihar Offline OP
hobbyist
OP Offline
hobbyist
M
Joined: Dec 2013
Posts: 20
Hi, My Denon x4000 AudysseyXT32 consistently sets my rear surround QS8 speakers at a cross-over of 200Hz. At the same time, Audyssey sets my R/L surround QS8s at 150Hz.

Audyssey should be identifying the speakers' roll-off frequency according to what Audyssey is telling me. This concerns me for 3 reasons.

1) The two settings are different for the surrounds/back sets of QS8s suggesting the two sets of QS8s v3 are performing differently.

2)Both sets appear to be performing significantly above (worse than) the advertised frequency response. They should start rolling-off around 100Hz or so.

3) I can detect a higher pitch in the right back surround compared to the others during the AudysseyXT32 test which could support a defect argument along with 1)

Has anyone had a similar experience? For those using AudysseyXT32 with the QS8s, what are your cross-overs automatically set at.

I've always felt that my QS8 speakers sounded very tinny to the point where its difficult to listen when playing 2 channel audio through Multi Channel Stereo.

Should I be considering getting the one speaker exchanged? Is it possible all 4 of my QS8s are defective? I bought them as factory seconds.

Cheers,


2)

Last edited by mrihar; 11/13/15 09:04 PM.
Re: QS8 Roll-off Frequency
mrihar #415473 11/13/15 09:19 PM
Joined: Apr 2003
Posts: 16,441
shareholder in the making
Offline
shareholder in the making
Joined: Apr 2003
Posts: 16,441
No, your speakers are most likely not defective. A speaker's placement in the room has a huge effect on what it will sound like from any given listening position. The Audyssey MutiEQ process does take audio samples from multiple positions in the listening area, so it should get a more accurate picture of a speakers performance, but the effects of the room cannot be downplayed.

That being said, I'd experiment with manually overriding the cutoff frequency on your sides are rears by setting them to 100Hz. If you think they sound tinny, this probably won't help because it will simply move some of the bass from the sub channel back to the side/rear surrounds.

Re: QS8 Roll-off Frequency
mrihar #415474 11/13/15 11:53 PM
Joined: Jul 2009
Posts: 2,281
connoisseur
Offline
connoisseur
Joined: Jul 2009
Posts: 2,281
I would agree with the above post by pmbuko , this is definitely a room reflection/placement problem. Audyssey would set my QS4's at 60hz and I would raise it up to 80hz. I now use Dirac which does not control the crossover frequency , instead it measures the speaker full range and with my QS8's they extend down past 40hz though I still set my crossover to 80hz since I use 2 subs so no need to stress my surrounds. The room has a significant impact on how a speaker sound and reacts. Audyssey can also be guilt of exaggeration of the upper frequencies which is widely discussed in many forums. Share the layout of your room with a picture or diagram so others can help with placement and possible room treatment options.

Richard


DOG is GOD spelled backwards.
What others think of me is none of my business.
M80 V3 MY GLOSS Cherry
Re: QS8 Roll-off Frequency
mrihar #415475 11/14/15 01:39 AM
Joined: Oct 2012
Posts: 2,021
Likes: 1
B
connoisseur
Offline
connoisseur
B
Joined: Oct 2012
Posts: 2,021
Likes: 1
Swap the two pairs to confirm....



Re: QS8 Roll-off Frequency
mrihar #415476 11/14/15 03:18 AM
Joined: Dec 2008
Posts: 6,928
axiomite
Offline
axiomite
Joined: Dec 2008
Posts: 6,928
Make sure the drivers are working. I had a bad driver on one of my QS8s a few yrs ago which threw the Audyssey readings out of whack thereby setting the crossover very high.


Half of communication is listening. You can't listen with your mouth.
Re: QS8 Roll-off Frequency
mrihar #415499 11/16/15 04:46 PM
Joined: Dec 2013
Posts: 20
M
mrihar Offline OP
hobbyist
OP Offline
hobbyist
M
Joined: Dec 2013
Posts: 20
Thanks for the replies. I checked the QS8 drivers and they all appear to be vibrating under load. I also swapped the R/L surrounds with the R/L rear surrounds. Wiring, stands and outputs from the receiver are all still locked to the same original position. I then ran the AudysseyXT32 setup again using the same 8 reference points and the same heights on the tripod.

Turns out I get the same cross-over calibration at the same speaker locations. In short, the QS8s where were calibrated with a 150Hz cross-over were now set at 200Hz and vice versa. Thus, I have to conclude with the rest of you that the speakers are not defective.

I suppose I can try a manual cross-over setting of 80Hz. The 200Hz makes no sense at all considering the EP500 I have starts to roll-off at 150Hz thus leaving a big gap between 150Hz & 200Hz for the R/L Rear Surrounds.

Here's what my room looks like and what my current layout looks like. Actually I can't figure out how to attach a jpeg. I'll try to figure that out.

Re: QS8 Roll-off Frequency
mrihar #415528 11/19/15 12:39 AM
Joined: Dec 2007
Posts: 7,786
axiomite
Offline
axiomite
Joined: Dec 2007
Posts: 7,786
I'm pretty sure I had the same issue when I set my system up. I set the crossover manually for the surrounds.


Fred

-------
Blujays1: Spending Fred's money one bottle at a time, no two... Oh crap!
Re: QS8 Roll-off Frequency
mrihar #416636 01/22/16 01:45 PM
Joined: Jan 2012
Posts: 90
old hand
Offline
old hand
Joined: Jan 2012
Posts: 90
I had a similar issue with a set of outdoor speakers; it came down to the distance between the amp and speakers and the gauge size of the cables I was using.


M80 v3, 2 x Emotiva UPA-1 Monoblocks, XPA-5, UMC-1 PrePro
Pro-Ject RPM Genie, Carver C2 Phono Preamp

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,940
Posts442,457
Members15,616
Most Online2,082
Jan 22nd, 2020
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,840
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 402 guests, and 3 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4