Connecting EP500 to line output of receiver.
|
Joined: Mar 2003
Posts: 144
veteran
|
OP
veteran
Joined: Mar 2003
Posts: 144 |
I have a really basic problem. I just bought a used EP500 subwoofer, but I don't know how to connect it to the subwoofer line output of my receiver. I looked at the "manual" on Axiom's product page for the EP500, but it's not all that helpful. It refers to an XLR to RCA adapter, but I don't have such a thing. Any suggestions would be welcome.
Greg VP180, M80s, M22s, QS8(4), CSW S305s, EP500, Pioneer VSX-90 M2i, M3(2), Pio vsx-1020
|
|
|
Re: Connecting EP500 to line output of receiver.
|
Joined: May 2002
Posts: 10,654
shareholder in the making
|
shareholder in the making
Joined: May 2002
Posts: 10,654 |
Greg, unless there's some complication that you haven't mentioned, you simply connect a standard coaxial cable with RCA plugs on each end from the sub out of the receiver to the line input on the sub.
-----------------------------------
Enjoy the music, not the equipment.
|
|
|
Re: Connecting EP500 to line output of receiver.
|
Joined: May 2003
Posts: 18,044
shareholder in the making
|
shareholder in the making
Joined: May 2003
Posts: 18,044 |
Only the very, very newest EP500s (and all Axiom subs) use the XLR to RCA adapter. If it's used, the current manual probably doesn't apply, and the sub has a regular ol' RCA input (and a regular old RCA output). You can use either one.
I am the Doctor, and THIS... is my SPOON!
|
|
|
Re: Connecting EP500 to line output of receiver.
|
Joined: Nov 2009
Posts: 89
old hand
|
old hand
Joined: Nov 2009
Posts: 89 |
Was trying to figure that out too, cuz in the new EP500V2 pics on the main Axiom site, I couldn't see any RCA inputs nor outputs. May I ask why they were omitted? Thanks!
Velo DD18,2xAxiom EP500,2xeD A7-450,2xSVS PB13U,2xSVS SB13P,2xInfinity Kappa12mbm, 2xB&W PCS8
|
|
|
Re: Connecting EP500 to line output of receiver.
|
Joined: Jan 2004
Posts: 13,843 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,843 Likes: 13 |
Call Axiom, they might now.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Re: Connecting EP500 to line output of receiver.
|
Joined: Feb 2008
Posts: 1,005
connoisseur
|
connoisseur
Joined: Feb 2008
Posts: 1,005 |
On the new amps for the EP500 the RCA and XLR are one in the same. Axiom should have sent an adapter for this purpose. If you need to use RCA you use the RCA adapter and plug into the XLR imput on the back of the sub. If using XLR just plug in your cable and your off to the races. Mel
|
|
|
Re: Connecting EP500 to line output of receiver.
|
Joined: Mar 2003
Posts: 144
veteran
|
OP
veteran
Joined: Mar 2003
Posts: 144 |
There are line-in and line-out jacks, and I disconnected the RCA connector from my current (working) sub and plugged it into the EP500 line-in jack. But I hear nothing. There are various possibilities of course, but now I'm exploring the possibility that there's something about the connections I don't understand. There are small holes at the right of the line-in and line-out jacks -- what are those for?
I could try the high level inputs, but there are no high level outputs, so how is that supposed to work?
Is the XLR to RCA adapter a standard part? I have no experience with XLR connections. [Never mind this; I see there are adapters and XLR male to RCA male cables.]
Thanks for any clues.
Last edited by GregLee; 02/03/10 01:36 PM.
Greg VP180, M80s, M22s, QS8(4), CSW S305s, EP500, Pioneer VSX-90 M2i, M3(2), Pio vsx-1020
|
|
|
Re: Connecting EP500 to line output of receiver.
|
Joined: Jan 2004
Posts: 13,843 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,843 Likes: 13 |
Axiom often makes changes to their subs midstream, your best bet would be to call an actual Axiom employee (Jc, Brent, Alan, etc.) at the 800 number, they man the phones until late. Since they are priveleged to this information, than can give you a factual answer.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Re: Connecting EP500 to line output of receiver.
|
Joined: Aug 2007
Posts: 3,488 Likes: 9
connoisseur
|
connoisseur
Joined: Aug 2007
Posts: 3,488 Likes: 9 |
The "small holes" are, I guess, the 1/8" 12v triggers (which can be used to control power on/off for the sub).
See Mojo's signature
|
|
|
Re: Connecting EP500 to line output of receiver.
|
Joined: Mar 2003
Posts: 144
veteran
|
OP
veteran
Joined: Mar 2003
Posts: 144 |
The "small holes" are, I guess, the 1/8" 12v triggers (which can be used to control power on/off for the sub). Oh, I see. The manual diagram for the current model has them in different places. I moved my right speaker connectors temporarily over to the EP500 high level inputs, and I am hearing some bass, now. So that's a relief. Most likely, the line-level input is just broken -- it feels a little loose. So I guess I'll order a male XLR to male RCA cable (I hope that's right). Thanks for the help.
Greg VP180, M80s, M22s, QS8(4), CSW S305s, EP500, Pioneer VSX-90 M2i, M3(2), Pio vsx-1020
|
|
|
Forums16
Topics24,949
Posts442,510
Members15,619
|
Most Online2,082 Jan 22nd, 2020
|
|
0 members (),
1,063
guests, and
3
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|