Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 3 1 2 3
Crossover settings for mix of "old" and new?
#401896 03/14/14 07:35 PM
Joined: Dec 2007
Posts: 93
B
bluray Offline OP
old hand
OP Offline
old hand
B
Joined: Dec 2007
Posts: 93
Would this be a good starting point for crossover settings in this 5.1 setup?
Front l and r - M100 - 40
Center - VP180 v3 - 60
Rear - M22 v3 - 80
EP800 sub

Or would you take center up to 80 and M100s up to 60?

Amp rated at 500w at 4 ohms

Last edited by bluray; 03/14/14 07:35 PM.
Re: Crossover settings for mix of "old" and new?
bluray #401899 03/14/14 09:46 PM
Joined: May 2003
Posts: 18,044
shareholder in the making
Offline
shareholder in the making
Joined: May 2003
Posts: 18,044
Seems sensible to me.


I am the Doctor, and THIS... is my SPOON!
Re: Crossover settings for mix of "old" and new?
bluray #401905 03/15/14 12:39 AM
Joined: Jun 2003
Posts: 8,488
Likes: 1
T
axiomite
Offline
axiomite
T
Joined: Jun 2003
Posts: 8,488
Likes: 1
Shoot, I'd let those front speakers play full range.


bibere usque ad hilaritatem
Re: Crossover settings for mix of "old" and new?
tomtuttle #401908 03/15/14 01:43 AM
Joined: May 2002
Posts: 5,745
Likes: 17
axiomite
Offline
axiomite
Joined: May 2002
Posts: 5,745
Likes: 17
Originally Posted By: tomtuttle
Shoot, I'd let those front speakers play full range.

I agree.
Balance the subwoofer with the mains by ear and then let 'em rip!


"Those who preach the myths of audio are ignorant of truth."
Re: Crossover settings for mix of "old" and new?
bluray #401910 03/15/14 02:26 AM
Joined: May 2002
Posts: 10,654
shareholder in the making
Offline
shareholder in the making
Joined: May 2002
Posts: 10,654
Blu, it's curious that some owners of nearly full-range speakers and an excellent sub(such as the EP800)are hesitant to set the speakers at say, 80Hz rather than 40Hz. They're concerned about "wasting" a very small part of the speaker frequency range, while not expressing a similar concern about not using as much as half of the sub's range to its best effect.

As long as the sub isn't localized, setting the crossover to a higher number is the way to go, making maximum use of the frequencies it does best both because of inherent design together with the ability to locate it specifically for best reproduction of those frequencies.

A uniform 80Hz crossover is still suggested.


-----------------------------------

Enjoy the music, not the equipment.


Re: Crossover settings for mix of "old" and new?
bluray #401915 03/15/14 02:10 PM
Joined: Dec 2007
Posts: 93
B
bluray Offline OP
old hand
OP Offline
old hand
B
Joined: Dec 2007
Posts: 93
Thank you. I am going to split the difference between all of y'all's advice!
M100s at 60 Hz
VP180 and M22s at 80 Hz

Re: Crossover settings for mix of "old" and new?
bluray #401924 03/15/14 04:46 PM
Joined: Sep 2011
Posts: 1,767
E
connoisseur
Offline
connoisseur
E
Joined: Sep 2011
Posts: 1,767
Audyssey sees both my M22s & VP160 at 40 Hz.

Just to be different from the herd, I run them both at 60 Hz. Works just fine in my modest system...

TAM

Re: Crossover settings for mix of "old" and new?
bluray #401926 03/15/14 05:53 PM
Joined: Jan 2004
Posts: 13,849
Likes: 15
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,849
Likes: 15
actually it is not Audyssey that sets that. smile Audyssey just reports back to the receiver mfg the +3dB point measurement of the speaker in your room during the sweep. Each mfg has a different point at which they set a speaker to small or full range. Some are 40Hz, others are higher.


M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Re: Crossover settings for mix of "old" and new?
bluray #401930 03/15/14 07:04 PM
Joined: Sep 2011
Posts: 1,767
E
connoisseur
Offline
connoisseur
E
Joined: Sep 2011
Posts: 1,767
I actually wrote that Audyssey 'sees' (or more correctly hears) my M22s & VP160 as 40 Hz...

TAM

Re: Crossover settings for mix of "old" and new?
bluray #401940 03/16/14 06:42 AM
Joined: Sep 2011
Posts: 1,767
E
connoisseur
Offline
connoisseur
E
Joined: Sep 2011
Posts: 1,767
SirQ:

You are probably correct; however, I'm confused after reading your post again.

Am I wrong in thinking that when Audyssey tells my Denon AVR that the -3 Db point is ~40 Hz, it sets the Xover there but also sets them to 'small'? Why is Denon's suggested setting of 40 Hz for supposedly 'small' speakers?

The prevailing wisdom is to then manually set them higher (but never lower). I can see the reasoning for this - to let the subs take on more of the load in the <80 Hz region where they often work better than most mains.

Despite a lot of reading on this subject, I guess that I still don't really have a grasp of this tool...

TAM

Page 1 of 3 1 2 3

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,984
Posts442,691
Members15,643
Most Online2,699
Aug 8th, 2024
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,849
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 595 guests, and 0 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4