Get Free, Friendly, Expert Advice
Call 1-866-244-8796 or email

Designed and Manufactured in Canada Since 1980


AxiomAudio Blog

Blind Listening Tests

Sneak Peek into Axiom’s Current Research and Development

Axiom’s Newest Speaker: The In-Ceiling M3

Wall'O'Fame
Experimental Atmos
Greetings fellow Axiom owners...
Who's Online
1 registered (CV), 42 Guests and 5 Spiders online.
Key: Admin, Global Mod, Mod
Financing
Forum Stats
13330 Members
11 Forums
22922 Topics
405249 Posts

Max Online: 378 @ 02/24/13 04:33 PM
Top Posters
Ken.C 17791
pmbuko 16289
SirQuack 13341
CV 11237
MarkSJohnson 10942
Meanwhile On Facebook

☺ Wow - our 13,000 likes! Awesome! #thankful

Did you get your "Golden Email"? The great gift certificate email giveaway star...

Here's a helpful article for everyone looking at putting a new stereo or home th...

Interesting article about who's getting the money from streaming radio services...

Topic Options
Rate This Topic
#54 - 05/08/01 02:53 PM 16-gauge speaker wire
Anonymous
Unregistered


Hi,

My electrician told me 16 gauge speaker wire is enough
for my Epic surround isntallation, I thought 12 gauge
is recommended? (max wire length is about 25 feet)
Is there a recommended speaker thickeness,
and any brandnames recommended?

thanks.



Top
#55 - 05/11/01 06:14 AM Re: 16-gauge speaker wire
Ian Offline
President
aficionado

Registered: 03/13/01
Posts: 809
I would recommend following your electrician's suggestion. Speaker wire is one of those ongoing debates that is driven by a lot of hype and very little substance. You should try the following experiment. Take two sets of cables, one a standard 16 gauge wire and the other a high end cable of your choice. Have someone hook up your system with one of these cables and not tell you which one they used. Evaluate the sound and then ask them to switch cables again without your knowing which cable it is. Now evaluate the sound again and determine which one you prefer or if you find no difference. After this experiment decide on your cable.

Ian Colquhoun
President & Chief Engineer
_________________________
Ian Colquhoun
President & Chief Engineer

Top
#56 - 01/30/02 12:52 AM Re: 16-gauge speaker wire
Greg Offline
newbie

Registered: 01/30/02
Posts: 1
I have found that testing speaker cable is very hard if you have to shut down the system and swap cables to make the comparison. By the time you get it powered back up you have forgotten what the original set up sounded like. The best test that I have found is to use a stereo system that has a stereo/mono selector, you can test in the mono mode so that both channels have the exact same signal sent to the speakers. Put the speakers on both sides of the person who wants to make the comparison facing directly at them, make sure that they are equal distances from the listener. Connect the "good" cable to one speaker and the "cheap" cable on the other speaker. With the system set to mono you can instantly fade back and fourth between both cables using the balance control. I have found this to be a very accurate way to compare any cable.

As far as 16-gauge cable, I think that you are running on the thin side. If your amp has a very high current output you may notice a huge difference by using heavy gauge speaker cables. If you have a moderate power output and tend not to drive the speakers hard you may never know the difference.

The best demo that I have ever done was with my Parasound HCA 2003a amp, M80Ti speakers and a pile of different speaker cables. The Parasound amp is capable of insane output levels (300 watts @ 4 ohms and up to 60 amps of current per channel). I put the speakers about 15 feet apart faced at each other with me directly in the center, I tried everything from 24 gauge telephone wire to BI-wiring with Kimber 8-TC. The biggest difference was always noticed when I was playing music with deep bass passages at ear splitting levels. When I compared 18 gauge zip cord to the Kimber 8-TC it sounded like I added a very large powered sub to the system on the Kimber side, it was truly amazing. When I turned the volume down to reasonable levels the difference was still noticeable but not as dramatic. As long as I stayed above the 12 gauge thickness the difference between any of the cables was very small and more a matter of personal preference. I am not saying that there is not a difference between speaker cables, I just think that most of us can get by with any reasonable speaker cable that is of adequate size for the power levels you expect to achieve.

So with all of this said I would recommend 12 gauge or heavier speaker cable made from oxygen free copper having a high strand count (it just seems to bend easier and sound better). If money is not an issue I would suggest that you try some of the high-end speaker cables and see if you can find a difference.

Just my thoughts,
Greg





Top



Moderator:  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Home  |  Corporate Info  |  Products  |  Message Board  |  FAQs  |  Warranty  |  Site Map  |  Privacy Statement   |  Contact Us

©2014 Colquhoun Audio Laboratories Limited
All Rights Reserved.