paintable surface
|
Joined: Dec 2007
Posts: 257
local
|
OP
local
Joined: Dec 2007
Posts: 257 |
Well the wife now thinks the QS8s are going to stand out too much.
I know there is an option for paintable surface.
Anyone ever done this, and paint the grills as well.
I imagine this is more effort than just addressing the trim on the in-cabinets.
Mark Pio 94,SB3,BD30,A35,Pio 48AV.Pronto 7000 controlling all. Getting ready for 22s, 150 & QS8s.
|
|
|
Re: paintable surface
|
Joined: Jun 2003
Posts: 8,488
axiomite
|
axiomite
Joined: Jun 2003
Posts: 8,488 |
Dude. Next time get forgiveness instead of permission.
bibere usque ad hilaritatem
|
|
|
Re: paintable surface
|
Joined: May 2003
Posts: 18,044
shareholder in the making
|
shareholder in the making
Joined: May 2003
Posts: 18,044 |
I am the Doctor, and THIS... is my SPOON!
|
|
|
Re: paintable surface
|
Joined: Feb 2002
Posts: 1,625
connoisseur
|
connoisseur
Joined: Feb 2002
Posts: 1,625 |
What color are your walls? We can actually do the painting right at the factory if that's of any help! I know the grilles aren't what your wife has in mind, but here's a customer's home who had us do the speakers in-house:
|
|
|
Re: paintable surface
|
Joined: Sep 2004
Posts: 5,422
axiomite
|
axiomite
Joined: Sep 2004
Posts: 5,422 |
As someone who has painted many odd surfaces (even ones that refuse to take paint such as silicone caulk), it is all in the primer. I hate to even say this, but here is what I would do if forced to:
Remove the grill and tweeters/woofers, plus pull out the connection box in the back that holds the speaker wire clips. Basically, remove everything that you don't want paint on that can be removed. Carefully put painter's tape over the decal sticker in the back. This will all help to make it look like it was SUPPOSED to be painted.
Then, using a medium grade sandpaper maybe around 180-220 grit (remember the smaller the numbers, the more viscious it will attack the surface). Just a light, but even "scuffing" of the surface is what you want. Do not "rub" the surface, but lightly and slowly "swipe" the surface going "with the grain" so that it retains the wood texture look after painted. Take your time...
If you have some canned air or a compressor, blow the dust off of the surface and out of the woodgrain "pores". Then, using a damp (not wet) cloth, or better yet what is called a tack cloth, remove any and all dust from the surface. I've had some luck using even a cleaning product like "409" or "Windex" and spraying a cloth and then wiping the surface to help really make sure it is free of any grease or oils from your hands.
Now that the surface is prepped, decide how you are going to paint it. It would be ideal if you could paint a thin coat on ALL surfaces and then have it dry, but that would mean either hanging it or propping it up through one of the holes where the speakers were. Test out your mechanism before trying to hang or balance a painted speaker.
If you are going to spray, make sure that you plug any opening that is there because the speakers are missing. If rolling on paint, then you could probably cover the holes with painter's tape.
I have found that a spray primer is easy to use even if you aren't using a spray paint in the end. Make sure that the primer is designed to work with vinyl, and DON'T get the cheap stuff. You are going to be painting a $600 pair of speakers, spend $10 and not $2 on the primer. Remember that a couple of light coats is WAY better than a thick one. Test the spray on a piece of cardboard to get a good feel for how far away you need to be in order to be effective. Most primers want a 2nd or 3rd coat to be applied BEFORE the previous coat dries. Keep this in mind. Also, your 1st coat shouldn't completely cover the surface. If it does, then it is probably too thick and could end up with waves (like really wide "drips") on the surface. I would say that the 2nd coat would be really close to 100% coverage, and a 3rd coat should do it perfectly. Again, if you go too heavy, it will take fewer coats. Now, some super premium primers can do it in one coat, but they are usually applied with a comercial grade sprayer. I've also used primers that are in a spray can that claim "1 coat," but I still get better results doing a couple lighter coats.
So now it is drying after being primed.
Painting is a similar process. A couple light coats vs. one heavy one. Since you are trying to blend them into the wall, I am guessing a laytex interior paint. Just paint the speaker as you wish. A good quality paint can be brushed on and the brush marks will disappear. If you are in doubt, I like little foam rollers for something like this. Cloth rollers tend to leave a texture. Foam rollers are smoother. Take your time as this will be the finish layer to the speaker.
So at this point, you are letting the paint dry. After it is dry to the touch, but not fully cured, move any of the painters tape if possible, being careful around the edges that it doesn't pull up your finish. Let it completely cure (24 hours?) before putting the tweeters, woofers, speaker wire connection back on.
As for the grill, I have no idea. Any additional paint will reduce sound transmission through the grills as it basically decreases the "holes" that the sound can go through.
Farewell - June 4, 2020
|
|
|
Re: paintable surface
|
Joined: Sep 2004
Posts: 5,422
axiomite
|
axiomite
Joined: Sep 2004
Posts: 5,422 |
And there you go. While I wrote that huge response, you got the speaker grill answer, and an option from Axiom!
GO TEAM!
Farewell - June 4, 2020
|
|
|
Re: paintable surface
|
Joined: Dec 2007
Posts: 257
local
|
OP
local
Joined: Dec 2007
Posts: 257 |
Thanks everyone. Already had the painting speaker grills bookmarked. Since I will be rolling them, figured a 1:3 dilution would work nice.,
Was more curious if any of you have used the "paitable surface" option from Axiom and done it.
Mark Pio 94,SB3,BD30,A35,Pio 48AV.Pronto 7000 controlling all. Getting ready for 22s, 150 & QS8s.
|
|
|
Re: paintable surface
|
Joined: Oct 2006
Posts: 6,955
axiomite
|
axiomite
Joined: Oct 2006
Posts: 6,955 |
Is it just an illusion or is the speaker very crooked in that otherwise fancy home. Not that I'm perfect but it makes me chuckle that they would take the time to match the paint and then hang them crooked.
With great power comes Awesome irresponsibility.
|
|
|
Re: paintable surface
|
Joined: Sep 2004
Posts: 11,458
shareholder in the making
|
shareholder in the making
Joined: Sep 2004
Posts: 11,458 |
I think it's angled out a bit.
::::::: No disrespect to Axiom, but my favorite woofer is my yellow lab :::::::
|
|
|
Re: paintable surface
|
Joined: Oct 2006
Posts: 6,955
axiomite
|
axiomite
Joined: Oct 2006
Posts: 6,955 |
I took that into account and it still looks crooked. However, as I say, it may just be an illusion.
With great power comes Awesome irresponsibility.
|
|
|
Forums16
Topics24,947
Posts442,495
Members15,617
|
Most Online2,082 Jan 22nd, 2020
|
|
0 members (),
715
guests, and
1
robot. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|