Get Free, Friendly, Expert Advice
Call 1-866-244-8796 or email

Designed and Manufactured in Canada Since 1980


AxiomAudio Blog

Outdoor Speaker Placement

Speaker Placement: Unusual Room Layouts and Elevating Speakers

Positioning Floorstanding Speakers

Wall'O'Fame
Greetings fellow Axiom owners...
HG Rosewoods Part 3
Who's Online
0 registered (), 80 Guests and 4 Spiders online.
Key: Admin, Global Mod, Mod
Financing
Forum Stats
13295 Members
11 Forums
22826 Topics
403239 Posts

Max Online: 378 @ 02/24/13 04:33 PM
Top Posters
Ken.C 17741
pmbuko 16259
SirQuack 13318
CV 11140
MarkSJohnson 10832
Meanwhile On Facebook

A very fond farewell party last night . . . we miss you Noreen!

Hope everyone's got their summer favourite playlists cued up for the weekend! W...

(y) Love this customer review of the M2s! "the first time listening to my new a...

These LFR1100 speakers in custom Eggshell White are on their way to Taiwan (yes,...

Topic Options
Rate This Topic
#2031 - 03/13/02 02:26 PM M3 at loud volumes
Anonymous
Unregistered


Hello everyone

do you figure the M3 sounds strained at high volumes due to a lack of crossover for the midrange/woofer driver?

Top
#2032 - 03/14/02 09:17 AM Re: M3 at loud volumes
Ian Offline
President
aficionado

Registered: 03/13/01
Posts: 796
In fact a x-over consumes power. If the speaker design parameters can be met without, or with minimal, x-over components the effect will be less distortion at higher volumes when compared to the same components with a complex x-over using the same amplifier.
_________________________
Ian Colquhoun
President & Chief Engineer

Top
#2033 - 03/15/02 03:16 PM Re: M3 at loud volumes
ravi_singh Offline
connoisseur

Registered: 03/14/02
Posts: 1351
Loc: Montreal
Ah! i understand. I didn't know that. I thought that it might be distorting at loud volumes because it was having a hard time playing the lower sounds, but I see that is not the case.

have you been looking into the apparent problem that the M3's do no sound good at loud volumes? I do not play my speakers THAT loud so I have not really heard it.

Top
#2034 - 03/16/02 06:23 AM Re: M3 at loud volumes
Ian Offline
President
aficionado

Registered: 03/13/01
Posts: 796
Actually the M3s play very loud for the category they are in. It is important to remember that the M3 is a 6 1/2" 2-way design with good low bass extension. At some point the physical limitations of the design will reach its maximum output. This is going to vary widely depending on the source material but the large motor structure of the M3 will allow it to play quite loud without any distortion. For high volume in large rooms the options are to move up to an M22 or larger, or use a powerful sub to take over the bass frequencies and remove some of the load from the M3 woofer. It is also important to not confuse amplifier clipping with speaker distortion. Lots of bass at high volume will drain the power supply of most amplifiers quickly and change the output from music to distortion. This phenomenon is not speaker distortion but rather the speaker reproducing the distorted signal it is receiving. This is why the expense amplifiers (assuming the cost is justified) will have such large power supplies and remain sounding "warm", or better not distorted, when playing high dynamic source material.
_________________________
Ian Colquhoun
President & Chief Engineer

Top



Moderator:  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Home  |  Corporate Info  |  Products  |  Message Board  |  FAQs  |  Warranty  |  Site Map  |  Privacy Statement   |  Contact Us

©2014 Colquhoun Audio Laboratories Limited
All Rights Reserved.