Get Free, Friendly, Expert Advice
Call 1-866-244-8796 or email

Designed and Manufactured in Canada Since 1980


AxiomAudio Blog

Blind Listening Tests

Sneak Peek into Axiom’s Current Research and Development

Axiom’s Newest Speaker: The In-Ceiling M3

Wall'O'Fame
EP175v4 with M3v4
Jungle's HT
Who's Online
1 registered (fredk), 46 Guests and 5 Spiders online.
Key: Admin, Global Mod, Mod
Financing
Forum Stats
13336 Members
11 Forums
22944 Topics
405772 Posts

Max Online: 378 @ 02/24/13 04:33 PM
Top Posters
Ken.C 17809
pmbuko 16297
SirQuack 13344
CV 11269
MarkSJohnson 10965
Meanwhile On Facebook

Just two more days! Better tell your gift-givers! http://axiomaudio.com/holida...

So many people took advantage of the weekend sales! Lots of auditioning about t...

Only a few hours left to get a gift card worth up to 25% of your purchase! http:...

Four days to get in on the action!

Page 1 of 2 1 2 >
Topic Options
Rate This Topic
#384053 - 10/12/12 06:53 PM VP150 @ 8ohm
brwsaw Offline
connoisseur

Registered: 10/12/12
Posts: 1124
I'd really like to upgrade every speaker in my system to 8 ohm Axioms but the VP150 fits my center channel requirements best.
My current setup has a 6 ohm speaker running off an 8 ohm setting with no ill effects, at least none I'm aware of.
Will I wreck the VP150 if I connect it at 8 ohms?
Does the sound quality suffer?
_________________________
The Hobbit in HFR 3D was worth the wait.

Top
#384056 - 10/12/12 07:25 PM Re: VP150 @ 8ohm [Re: brwsaw]
fredk Online   happy
axiomite

Registered: 12/06/07
Posts: 7223
Loc: Canada
You will be just fine. Johnk will be along shortly with the full explanation.
_________________________
Fred

-------
Blujays1: Spending Fred's money one bottle at a time, no two... Oh crap!

Top
#384071 - 10/12/12 09:59 PM Re: VP150 @ 8ohm [Re: brwsaw]
JohnK Offline
shareholder in the making

Registered: 05/11/02
Posts: 10411
BRW, welcome. The first point is that you're paying too much attention to speaker impedance ratings. Speakers vary widely in their impedance as they play various frequencies; often the rated impedance is approached less than half the time.

Specifically as to the impedance setting on the receiver, the higher default setting, which may be labeled as 8 Ohms or 6 Ohms, should always be left in effect, regardless of the rated impedance of the speakers. Changing the setting to the lower impedance number is specified in manuals because of safety requirements of the UL(Underwriters Laboratories)relating to overheating(of the receiver)with low impedance loads. It does this by reducing the voltage output of the receiver's power supply section, which following Ohm's Law results in a reduction in current and power. Tests have shown that the maximum power capability is cut roughly in half at the lower impedance setting.

So, the maximum capability of the receiver is available at the default higher impedance setting, and the speakers would be in greater danger of being damaged by receiver clipping because of less clean power being available at the lower setting, which in no way can improve the sound of the speaker.

Never change the 8 ohm setting.
_________________________
-----------------------------------

Enjoy the music, not the equipment.



Top
#384076 - 10/13/12 02:32 AM Re: VP150 @ 8ohm [Re: JohnK]
brwsaw Offline
connoisseur

Registered: 10/12/12
Posts: 1124
Thanks.
VP150 it is.
_________________________
The Hobbit in HFR 3D was worth the wait.

Top
#385327 - 11/08/12 10:30 PM Re: VP150 @ 8ohm [Re: brwsaw]
brwsaw Offline
connoisseur

Registered: 10/12/12
Posts: 1124
If anyone's still reading this thread, maybe they could comment on using the VP 180 with the receiver at 8 ohm.It would likely be the only speaker not 8 ohm if we go ahead with it.
It seems this has been beat to death but it would be a shame to ruin either the receiver and or the speaker.

JohnK?


Edited by brwsaw (11/08/12 10:31 PM)
_________________________
The Hobbit in HFR 3D was worth the wait.

Top
#385329 - 11/08/12 11:00 PM Re: VP150 @ 8ohm [Re: brwsaw]
Ken.C Offline
shareholder in the making

Registered: 05/03/03
Posts: 17809
Loc: NoVA
It'll be fine. Remember that the 4 ohm/8 ohm switch actually limits current which could result in damage to the speaker (when set to 4 ohms). Always leave the switch on 8 ohms.
_________________________
I am the Doctor, and THIS... is my SPOON!

Top
#385335 - 11/09/12 12:10 AM Re: VP150 @ 8ohm [Re: brwsaw]
JohnK Offline
shareholder in the making

Registered: 05/11/02
Posts: 10411
It may have been "beat to death", but apparently the point still isn't clear: to get the clean maximum power for which the receiver was designed, it's necessary to use the full capacity of its power supply section, not cripple it by limiting the voltage output.
_________________________
-----------------------------------

Enjoy the music, not the equipment.



Top
#385350 - 11/09/12 08:49 AM Re: VP150 @ 8ohm [Re: brwsaw]
Murph Offline
axiomite

Registered: 10/05/06
Posts: 6884
Loc: PEI, Canada
_________________________
With great power comes Awesome irresponsibility.

Top
#385351 - 11/09/12 08:53 AM Re: VP150 @ 8ohm [Re: brwsaw]
Murph Offline
axiomite

Registered: 10/05/06
Posts: 6884
Loc: PEI, Canada
Sorry John, I couldn't help myself.

If only forum search buttons were not so frustrating to use. I hate saying "Please use the Search button." because I know I have trouble getting decent results myself.
_________________________
With great power comes Awesome irresponsibility.

Top
#385353 - 11/09/12 09:11 AM Re: VP150 @ 8ohm [Re: brwsaw]
Ken.C Offline
shareholder in the making

Registered: 05/03/03
Posts: 17809
Loc: NoVA
But haven't you asked this question at least once before, brwsaw?
_________________________
I am the Doctor, and THIS... is my SPOON!

Top
Page 1 of 2 1 2 >



Moderator:  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Home  |  Corporate Info  |  Products  |  Message Board  |  FAQs  |  Warranty  |  Site Map  |  Privacy Statement   |  Contact Us

©2014 Colquhoun Audio Laboratories Limited
All Rights Reserved.