Get Free, Friendly, Expert Advice
Call 1-866-244-8796 or email

Designed and Manufactured in Canada Since 1980


AxiomAudio Blog

Axiom’s Newest Speaker: The In-Ceiling M3

Outdoor Speaker Placement

Speaker Placement: Unusual Room Layouts and Elevating Speakers

Wall'O'Fame
Greetings fellow Axiom owners...
HG Rosewoods Part 3
Who's Online
1 registered (CV), 149 Guests and 4 Spiders online.
Key: Admin, Global Mod, Mod
Financing
Forum Stats
13303 Members
11 Forums
22841 Topics
403596 Posts

Max Online: 378 @ 02/24/13 04:33 PM
Top Posters
Ken.C 17751
pmbuko 16267
SirQuack 13321
CV 11160
MarkSJohnson 10848
Meanwhile On Facebook

Get a Gift Card Worth 20% of Your Purchase! Save hundreds!

Got your new In-Ceiling speakers yet? #atmosready http://axiomaudio.com/m3-in-c...

(y) Can't wait for the next evolution of surround sound to go mainstream!

Pre-order our new in-ceiling speakers and save 25%! Offer ends August 11th.

Page 2 of 2 < 1 2
Topic Options
Rate This Topic
#389619 - 02/11/13 10:24 AM Re: Pre outs signal [Re: Jasper]
alan Offline
connoisseur

Registered: 01/29/02
Posts: 3186
Loc: Toronto/New York/Dwight
Hi Jasper,

You're not risking grief or damage to the electronics or your speakers with your current setup.

It's just that you're running the audio signals through two preamp sections and two volume controls, because the PM16 is not a basic power amplifier and lacks power-amp inputs. It makes for a somewhat convoluted setup, with two volume controls to adjust when there should only be one.

Regards,
Alan
_________________________
Alan Lofft,
Axiom Resident Expert

Top
#389640 - 02/11/13 08:57 PM Re: Pre outs signal [Re: Jasper]
jakewash Offline
shareholder in the making

Registered: 12/26/03
Posts: 10398
Loc: Calgary, Alberta
Try it with out the PM 16(with out Audyssey but level matched) and then try it with the PM 16(with out Audyssey and level matched) and then have fun trying to decide which way it sounds better if there is any difference. If you don't hear a difference then you might as well make things easy and leave the PM-16 out of it.
_________________________
Jason
-----------------
TTTHHHPPPPPTTTT!

My HT

Top
#389647 - 02/11/13 10:02 PM Re: Pre outs signal [Re: Jasper]
FATMANBLOWFISH Offline
regular

Registered: 05/17/07
Posts: 7
Loc: THOROLD, ONTARIO
By grief I meant having to adjust (and I would guess constantly re-adjust as sources were changed) both units to try to get the sound you want - not any physical damage to the equipment.

Top
#389648 - 02/11/13 10:13 PM Re: Pre outs signal [Re: Jasper]
JohnK Offline
shareholder in the making

Registered: 05/11/02
Posts: 10372
Jasper, "grief" wasn't described, but as Alan pointed out, the theoretical objection is that the sound runs through two preamp sections rather than one, adding a small amount of extra distortion. This is unlikely to be audible, and if you like to use the PM16, carry on.

If the main speaker level trim was set in the 6004 to the minimum -12dB available(possibly indicating a lower setting was wanted)during calibration, lower the PM16 volume control a bit so that the calibration number comes out higher.

Edit: Roy, once the level is properly calibrated, the PM16 level control wouldn't have to be changed; any volume changes would be done in the 6004.
_________________________
-----------------------------------

Enjoy the music, not the equipment.



Top
Page 2 of 2 < 1 2



Moderator:  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Home  |  Corporate Info  |  Products  |  Message Board  |  FAQs  |  Warranty  |  Site Map  |  Privacy Statement   |  Contact Us

©2014 Colquhoun Audio Laboratories Limited
All Rights Reserved.