Previous Thread
Next Thread
Print Thread
Rate Thread
Page 1 of 3 1 2 3
Understanding how a sub works
#216765 07/29/08 08:46 PM
Joined: Jul 2008
Posts: 11
G
frequent flier
OP Offline
frequent flier
G
Joined: Jul 2008
Posts: 11
Hey guys,

I am trying to get my head wrapped around some subwoofer questions. I am sure someone will be able to help me out here...

When I am using a powered subwoofer with its own amp, I am sending pre-amp signal from my AVR to my sub, correct? Now this signal, does it only carry the frequencies (in the form of current) or information about the "volume" as well. What I am trying to say is that with the subwoofer volume at a certain level, how does it decide that the explsions are supposed to be louder than lets say a person falling on a wooden floor. What information does a pre-amp LFE signal carry to the amp of a power subwoofer.
Thanks

Re: Understanding how a sub works
geoffthemonk #216766 07/29/08 09:19 PM
Joined: Apr 2003
Posts: 16,441
shareholder in the making
Offline
shareholder in the making
Joined: Apr 2003
Posts: 16,441
Hi geoffthemonk,

Welcome. You have some good questions -- as if there is any other kind... ha!

The signal your AVR sends to the subwoofer is tied to the volume knob, just as the rest of the channels are. All the level adjustment is done in the pre-amp stage before it is sent on to the amplifiers (internal or external). In that sense, the information the AVR sends to the sub is no different than the information it sends to its internal amps.

Does that clear it up?

Re: Understanding how a sub works
geoffthemonk #216801 07/30/08 03:50 AM
Joined: May 2002
Posts: 10,654
shareholder in the making
Offline
shareholder in the making
Joined: May 2002
Posts: 10,654
Geoff, it's a widely varying voltage(not current)from the sub pre-out of the receiver that makes the difference in loudness. The output into the internal sub amplifier might vary from a full volt or a bit more down to a small fraction of a volt for more quiet moments. The sub amplifier then takes this voltage and increases it about 30 times(a "gain" of about 29dB)so that it's high enough to operate the subwoofer driver.


-----------------------------------

Enjoy the music, not the equipment.


Re: Understanding how a sub works
JohnK #216880 07/30/08 09:16 PM
Joined: Jul 2008
Posts: 11
G
frequent flier
OP Offline
frequent flier
G
Joined: Jul 2008
Posts: 11
So here is my issue, my sub (an EP350) doesnt seem to be doing for me what I expect from it. I cant seem to be able balance it with my M60s. It is either too high or too low. I used YPAO that my Yammy 663 has. I am not getting the thum I am looking for. At lower volume, I am hardly getting any bass. I need to be above -20dB (receiver volume) before I start hearing any bass at all. I am attaching some pictures of how my room is layed out, It will be great if someone could help me with getting my sub to do what it must.
My home theater is in my living room. This first picture is taken from the left side of the room.

http://i310.photobucket.com/albums/kk429/geoffthemonk/IMG_2818.jpg

The three stackable table on the near side of the pic is where my sib is (shown in the next pic, this living room opens into a kitchen seen in the far side of the picture. The living room is 28' x 14'3". The TV and couc are on the width side of the room.
The kitchen is 16' x 9' (can be seen behind the staircase.
Here is the second pic that shows where the sub is right now..

http://i310.photobucket.com/albums/kk429/geoffthemonk/IMG_2817.jpg
The sub is under the tallest of the three stackable tables. This third picture is taken from the staircase side standing in the kitchen entrance....
http://i310.photobucket.com/albums/kk429/geoffthemonk/IMG_2819.jpg

It also shows where the M60s and VP150 are. This last one shows the QS8s.

http://i310.photobucket.com/albums/kk429/geoffthemonk/IMG_2821.jpg

Do you guys think my sub is just in a really really bad spot. Is it a must that I move it from where it is right now?

Thanks

Re: Understanding how a sub works
geoffthemonk #216882 07/30/08 09:34 PM
Joined: Jan 2004
Posts: 13,849
Likes: 15
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,849
Likes: 15
Do you have your speakers set to "small" in the receiver setup? Often the auto setup in receivers turn your speakers to large. You want all speakers set to small with an 80hz crossover in the receiver. You want the crossover on the back of the sub cranked to the highest setting, to get it out of the way for the receiver to manage.

If you ran the auto setup, the sub and speakers should be calibrated to the correct SPL levels, but it might not be a bad idea to verify with a Radio Shack meter.

Do you have the distanc (delay) setting in the receiver correct for the sub. Looks like it would only be a few feet from the couch.

Have you tried adjusting the phase switch on the sub. Normally, you want it up near the front speakers for best blend, with a 0 phase setting. You might try adjusting this to see if it helps.

Keep in mind most music does not have lowwww frequencies, unless you listen to rap or r&b. What about movies with low LFE, how does it work for those?

Is this an older 350 or one of the new 350's? Either way you want it calibrated to the same levels with the receiver pink noise tests.


M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Re: Understanding how a sub works
SirQuack #216890 07/30/08 10:21 PM
Joined: Oct 2006
Posts: 6,955
axiomite
Offline
axiomite
Joined: Oct 2006
Posts: 6,955
Great Advice!
Autosetup can play havoc with subs. Also look for any extra LFE settings that your Yammy might have.

My Denon, for instance, had a second setting (other than the main db setting for the sub) that was meant only to apply to DTS sound tracks. It was set for 10db in the difference and really confused me until I found it. This isn't exactly your issue but just an example of an extra setting that might not be so obvious.


With great power comes Awesome irresponsibility.
Re: Understanding how a sub works
SirQuack #216891 07/30/08 10:23 PM
Joined: Jul 2008
Posts: 11
G
frequent flier
OP Offline
frequent flier
G
Joined: Jul 2008
Posts: 11
sirquack, you are right, the YPAO sets mains to large but I always run them as small. My corssover is set at 80Hz, x-over on the sub is always all the way up (I adjust x-ver from the AVR), I do not have a delay settin in my receiver for the sub. I ave tried both 0 and 180 for the phase, not much affect. Like I said, the volume on my sub has to be fairly high to get any 'thump' from the sub. I have the sub volume set at about 12o'clock. Cranking it up helps a little but not a ton. Sub gain is set to 3.5 in my AVR. This is an EP350V2, not the V3.
Does anyone think/feel that 200W RMS amp just didint have enough juice to drive this 12-in driver and that is the reason why V3 has a beefier 300W RMS amp?

Re: Understanding how a sub works
SirQuack #216892 07/30/08 10:24 PM
Joined: May 2003
Posts: 18,044
shareholder in the making
Offline
shareholder in the making
Joined: May 2003
Posts: 18,044
You should also double check that the sub is actually turning on at low volume; you may need to boost the output from the receiver and lower it on the sub to get enough signal at lower volumes to trigger the auto-on.


I am the Doctor, and THIS... is my SPOON!
Re: Understanding how a sub works
Ken.C #216894 07/30/08 10:38 PM
Joined: Apr 2008
Posts: 274
local
Offline
local
Joined: Apr 2008
Posts: 274
 Originally Posted By: kcarlile
You should also double check that the sub is actually turning on at low volume; you may need to boost the output from the receiver and lower it on the sub to get enough signal at lower volumes to trigger the auto-on.

My thoughts exactly -- I've seen several reports of this happening.

Re: Understanding how a sub works
anthony11 #216899 07/30/08 11:27 PM
Joined: Jan 2004
Posts: 13,849
Likes: 15
shareholder in the making
Offline
shareholder in the making
Joined: Jan 2004
Posts: 13,849
Likes: 15
Performance wise, I think there is a great difference between the 350v2 and v3. I've owned them both. The v2 did a respectable job in my larger room. However, the V3 has a different amp design and driver. I know in Alan's review, he said the new 350 was comparable to the EP500 in some respects.

So your receiver does not allow you to set the distance from the primary listening position to each speaker, or are you saying you just can't for the sub? This seems odd, even my old prologic receivers from the early 90's allowed for this delay setting.


M80s VP180 4xM22ow 4xM3ic EP600 2xEP350
AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85


Page 1 of 3 1 2 3

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,984
Posts442,691
Members15,643
Most Online2,699
Aug 8th, 2024
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,849
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 595 guests, and 0 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4