Crossover setting for VP180 at 40hz?
|
Joined: Apr 2012
Posts: 78
old hand
|
OP
old hand
Joined: Apr 2012
Posts: 78 |
I have always left my VP180 center channel at 60hz crossover. Well, the other day I was re-running Audyssey and accidentally set the center to large and the front M80's to small. I noticed a very nice improvement in the sound. The center sounded more full and rich. I know the best advice is NOT the set the center to FULL, but what about 40hz while leaving the M80's at 60hz?
Does anyone here use this as their default setting?
Any disadvantages?
Thoughts?
Last edited by VoicOfReason; 04/21/13 09:30 PM.
Epson 8350 * Denon 4311CI * XPA-5 * M80/VP180 * 2 QS8's+M2v3-DSX * SVS PC13-Ultra ** Buttkicker LFE
|
|
|
Re: Crossover setting for VP180 at 40hz?
|
Joined: May 2002
Posts: 10,654
shareholder in the making
|
shareholder in the making
Joined: May 2002
Posts: 10,654 |
Peter, some clarification of what you in fact did is necessary. When the front speakers are set "Small", none of the other speakers, including the center, can be set "Large".
-----------------------------------
Enjoy the music, not the equipment.
|
|
|
Re: Crossover setting for VP180 at 40hz?
|
Joined: Apr 2012
Posts: 78
old hand
|
OP
old hand
Joined: Apr 2012
Posts: 78 |
Sorry. Yes, you are correct. It was the crossover I set wrong at first. The center was at 40hz and fronts were at 60hz. It sounds better this way, I think. Any disadvantages? Do soundtracks usually even send a lot of LFE/low level information to the center channel anyway?
Epson 8350 * Denon 4311CI * XPA-5 * M80/VP180 * 2 QS8's+M2v3-DSX * SVS PC13-Ultra ** Buttkicker LFE
|
|
|
Re: Crossover setting for VP180 at 40hz?
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
Also, you never want to lower the crossover (ok to set higher) from the setting that was configured by your receiver after running Audyssey. For ex, if Audyssey reports back to your Denon that the -3dB point of a particular speaker is 80Hz, the Denon would set the speaker as "small" with an 80Hz crossover, as Denon uses 40Hz as the determining factor. You would never lower that value, but raising is ok.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Re: Crossover setting for VP180 at 40hz?
|
Joined: Sep 2004
Posts: 5,422
axiomite
|
axiomite
Joined: Sep 2004
Posts: 5,422 |
My Onkyo receiver sets my VP180 to 40hz every time I've run it. Some time I leave it, sometimes I bump it up to 60 or 80hz. Like Randy states, that is OK, wit Audyssey because you are basically removing calibration extension in the lower frequencies. However, if it sets something to, say, 80hz, and you drop it down to 60hz, Audyssey hasn't done any room calibration down between the original 80hz and your new 60hz setting.
Farewell - June 4, 2020
|
|
|
Re: Crossover setting for VP180 at 40hz?
|
Joined: Apr 2012
Posts: 78
old hand
|
OP
old hand
Joined: Apr 2012
Posts: 78 |
Yeah, Audyssey sets everything in front to 40hz default, for me.
Epson 8350 * Denon 4311CI * XPA-5 * M80/VP180 * 2 QS8's+M2v3-DSX * SVS PC13-Ultra ** Buttkicker LFE
|
|
|
Re: Crossover setting for VP180 at 40hz?
|
Joined: Sep 2004
Posts: 5,422
axiomite
|
axiomite
Joined: Sep 2004
Posts: 5,422 |
It sets my M60s to 60hz in comparison.
Farewell - June 4, 2020
|
|
|
Forums16
Topics24,945
Posts442,481
Members15,617
|
Most Online2,082 Jan 22nd, 2020
|
|
1 members (FordPrefect),
689
guests, and
3
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|