Re: I need some help with room analysis and treatment…
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
Yeah, you don't need speaker cloth for bass traps, or first reflection panels for that matter. As Ethan always said, if you can blow through it with your breath and feel it on the other side with your hands it will work. Many people use even burlap material for bass traps. Bass freq's go right through. I would not pay extra for speaker grill material, JoAnns or even places like Walmart should have some black stretchy material much cheaper.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Re: I need some help with room analysis and treatment…
|
Joined: Dec 2007
Posts: 7,786
axiomite
|
axiomite
Joined: Dec 2007
Posts: 7,786 |
Have any of you guys checked out Ethan's bio? The guy is quite amazing. He was a programmer who ran his own company, took up the chello (I think) in his 30s or 40s and became a professional musician and now runs a company making acoustic treatments.
Fred
------- Blujays1: Spending Fred's money one bottle at a time, no two... Oh crap!
|
|
|
Re: I need some help with room analysis and treatment…
|
Joined: Jul 2004
Posts: 4,444 Likes: 16
connoisseur
|
OP
connoisseur
Joined: Jul 2004
Posts: 4,444 Likes: 16 |
What's the simplest way to do a quick before / after sweep? I see where a lot of folks on this board post before / after trends.
I'm assuming that I download and install Real Traps. It looks as if I use my RS digital meter.
Yes, I'm being lazy. I start reading and get glossy eyed. I’m looking for a real simple, step by step cheat sheet of sorts.
|
|
|
Re: I need some help with room analysis and treatment…
|
Joined: Dec 2007
Posts: 7,786
axiomite
|
axiomite
Joined: Dec 2007
Posts: 7,786 |
REW is the best way to do sweeps, once you get it set up. Its not that complicated, but there is a learning curve.
Hauling traps around is always fun...
Fred
------- Blujays1: Spending Fred's money one bottle at a time, no two... Oh crap!
|
|
|
Re: I need some help with room analysis and treatment…
|
Joined: Dec 2008
Posts: 1,361
connoisseur
|
connoisseur
Joined: Dec 2008
Posts: 1,361 |
This is getting complicated. The more I read on Ethan’s page, the more confused I get. My lil project is on hold till I can figure this crap out a bit better. I’m not even sure I can use the fabric I bought. Ethan says you should be able to blow threw the fabric with relative ease. The stuff I bought takes effort. So if I use it, it will reflect high frequencies. Not sure if I want that to happen, it doesn’t sound good. There’s deep bass, mid bass, high bass, mid-high frequencies. All require different trap building techniques.
I had an interesting (to me!) experience at an NBA game on Wednesday. Sitting in the nosebleed section, I was able to see the speaker array used, up close. To my surprise, it was not of the normal rock band size. Not small, but not what I remember from Van Halen or Metalica concerts. But, even in this massive open and hard sided arena, the bass at my seat was solid as a brick to the gut (call it bowel shaking ), with no thunder decay or muddiness at all. The more I paid attention, I was surprised that the music was very solid and clear, the announcer’s voice was clear, and there was no echo at all, despite the cavern of cement under a steel roof. So I started to look for the acoustic secret – and I found it. First, human flesh. There was lots of it. But more importantly, I think, from the ceiling they had large rubber mats, suspended in a weak U shape. Lots of them. That was all I could see after close scrutiny. That got me thinking about some of our discussions here about the need to be able to blow through the material, the depth of insulation, etc. Relatedly, it reminded me of the well accepted use of sound deadening material on the auto side. I know “those bass heads” have nothing offer true audiophiles (even if half the people on this thread have more subwoofers than 80% of those "mobile" bastards), but I have used several products to kill the road noise in my SUV, with exceptional results. Those products, like the rubber mats at the arena, use a rubber or tar based membrane to convert sound energy to heat. These products are less than a quarter of an inch thick, and the rubber mats at the arena were no more than an inch thick (and about 3 feet wide). Why then, in the more heady home audiophile realm, are we constantly talking about compressed fiberglass 12 inches thick to kill a bass note or stop an echo? Has anyone seen a study of the acoustic properties of thin rubber and tar membrane products as compared to fiberglass? Please give us your thoughts on this, as we could all benefit from a half-inch solution to a 12 inch problem. . . that did not come out right. Below are a few cites I have used to learn a bit about the tar based products for anyone interested: Tech Talk Jay Leno uses it B-Quiet Background
Panny 3000 PJ, 118" Carada, Denon 3300, PS3, Axiom QS8, PSB 5T, B&W sub, levitating speaker wire
|
|
|
Re: I need some help with room analysis and treatment…
|
Joined: Feb 2009
Posts: 562
aficionado
|
aficionado
Joined: Feb 2009
Posts: 562 |
REW is the best way to do sweeps, once you get it set up. Its not that complicated, but there is a learning curve. What is "REW" ? Can someone (not too) briefly explain the process and what is needed to get this graph info? Does this process give you a graph, or just individual data points you manually put onto a graph? I assume you need a laptop (not Mac), a RS SPL meter and this 'REW'. (working to abolish [my] ignorance.;o)
Dave
"In theory, practice and theory are the same. In practice they're not."
|
|
|
Re: I need some help with room analysis and treatment…
|
Joined: Dec 2003
Posts: 10,420
shareholder in the making
|
shareholder in the making
Joined: Dec 2003
Posts: 10,420 |
Jason M80 v2 VP160 v3 QS8 v2 PB13 Ultra Denon 3808 Samsung 85" Q70
|
|
|
Re: I need some help with room analysis and treatment…
|
Joined: Jul 2004
Posts: 4,444 Likes: 16
connoisseur
|
OP
connoisseur
Joined: Jul 2004
Posts: 4,444 Likes: 16 |
You might find reading through the REW user guide to be more helpful than wading into those forums. I found the forums to be for advanced users who actually knew what the heck they are doing. http://www.hometheatershack.com/roomeq/wizardhelp/help_en-GB/html/gettingstarted.html#top I don't think I'm going to mess with it. My laptop doesn't have enough memory or a good enough sound card......or so I think.
Last edited by mdrew; 03/27/09 09:41 PM.
|
|
|
Re: I need some help with room analysis and treatment…
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
I used to use REW, but have had issues getting the sound card setup, using the REW interface is not exactly for newbies, and the SPL meter is not really a great Mic. I recently came across this Frequency Response Plotter which seems to do an awesome job, and is very easy to use. Yes, I've been graphing again, and have some very impressive results. Oh yeah, and I've found that using my Mic that came with my Denon does a better job than my SPL meter as a mic, seems more accurate.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Re: I need some help with room analysis and treatment…
|
Joined: Dec 2003
Posts: 10,420
shareholder in the making
|
shareholder in the making
Joined: Dec 2003
Posts: 10,420 |
But the RS meter has Calibration files that you use to adjust for it's short comings, making its reading very reliable.
Jason M80 v2 VP160 v3 QS8 v2 PB13 Ultra Denon 3808 Samsung 85" Q70
|
|
|
Forums16
Topics24,945
Posts442,486
Members15,617
|
Most Online2,082 Jan 22nd, 2020
|
|
0 members (),
1,217
guests, and
4
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|