Safe Audio Volume?
|
Joined: Dec 2010
Posts: 30
enthusiast
|
OP
enthusiast
Joined: Dec 2010
Posts: 30 |
I have 4QS8's and have blown the woffers recently so I need advice on the max safe volume I should not exceed (in absolute NOT dB's.) Currently my QS8's are at -5dB and my volume is set to absolute. I like to watch my movies at about 85 absolute volume but when serious surround kicks in I'm afraid it's to much. My receiver outputs 125W/channel. Thanks.
Samsung 65" 3D LCD TV, Samsung 3D Blu-Ray Disc Player, Denon AVR 3311CI, EP800, M80's, VP150, 4QS8's
|
|
|
Re: Safe Audio Volume?
|
Joined: Jan 2011
Posts: 1,291
connoisseur
|
connoisseur
Joined: Jan 2011
Posts: 1,291 |
those QS8 can take much more power than your receiver puts out. first guess is you overdrove (to clipping) the amps feeding the QS8's.
if your system is well setup with no bass/treble boost, and if you listen to music or movies at realistic levels, then you should not be overdriving the amps/speakers. when you overdrive an amp, the output power can be much more than what the specs say, but this overdriving produces distortion in the sound, and it can blow up speakers very easily. As soon as you hear some distortion, that indicates you're overdriving the amp; you should then lower the volume enough that there is no distortion at all. If you hear speaker bottoming, that's even worse.
What's the size of your AV room? If it's a very large room, then maybe you don't have enough power to get realistic levels without clipping the amps.
I've never used "absolute", so i can't comment on that.
Last edited by J. B.; 09/18/11 02:59 PM.
|
|
|
Re: Safe Audio Volume?
|
Joined: Dec 2008
Posts: 6,928
axiomite
|
axiomite
Joined: Dec 2008
Posts: 6,928 |
I agree with JB. It's likely your amp has been driven into clipping as the QS8s can handle considerably more power than you are giving them.
Half of communication is listening. You can't listen with your mouth.
|
|
|
Re: Safe Audio Volume?
|
Joined: Sep 2008
Posts: 4,116
connoisseur
|
connoisseur
Joined: Sep 2008
Posts: 4,116 |
My first thought is to check your bass management setting, specifically the large/small settings on your QS8's. If you have them set to large, set them to small with a 80hz or 90hz crossover point. Having them set to large could surely stress the woofers and perhaps blow them if you are watching movies at close to reference level. You are also wasting a bit of amp power as any content sent to the surrounds below 80hz could be amplified by the subwoofer.
If it's the receiver that is clipping badly, it's the tweeters that will generally get fried.
I’m armed and I’m drinking. You don’t want to listen to advice from me, amigo.
-Max Payne
|
|
|
Re: Safe Audio Volume?
|
Joined: Jan 2011
Posts: 1,291
connoisseur
|
connoisseur
Joined: Jan 2011
Posts: 1,291 |
if you would like to know exactly when your amp is clipping, without having to guess, get amps that have LED clipping lights; for me, it's the surest way i know of. another way is to hookup your amp output with an oscilloscope in parallel with one of the front speakers. then you can see very clearly when clipping happens.
|
|
|
Re: Safe Audio Volume?
|
Joined: Jul 2004
Posts: 1,443
connoisseur
|
connoisseur
Joined: Jul 2004
Posts: 1,443 |
You DO have an oscilloscope?
"A fanatic is someone who can't change his mind and won't change the subject" Churchill
|
|
|
Re: Safe Audio Volume?
|
Joined: Jan 2011
Posts: 1,291
connoisseur
|
connoisseur
Joined: Jan 2011
Posts: 1,291 |
i used to have one, since the 70s up to a few years ago; it was always connected to my audio system. this is how i discovered that my Hafler 500 amp had an instantaneous power output on music peaks of 735 Watts/ch.; pretty good dynamic headroom. Rated continuous power was around 250W/ch/8 Ohms.
sometimes, as a show to some people, i used to connect the LF and the RF each to an oscilloscope input; that would show phasing between the 2 channels, and it made for an interesting visual rendition of the music that was playing
|
|
|
Re: Safe Audio Volume?
|
Joined: Dec 2010
Posts: 30
enthusiast
|
OP
enthusiast
Joined: Dec 2010
Posts: 30 |
My AV room (living room) is about 25' x 18' but opens up into an office and kitchen. I think I need an amplifier but the Axiom A1400-8 is to expensive for me. Any suggestions on a cheaper amplifier? I'm thinking half the price of the A1400-8. Also, I'm not trying to make my ears bleed, just want my surrounds with more safe overhead.
I have left the surrounds at -5 dB because that is where the auto calibration set them. I have set the M80's at -12dB (the lowest channel volume) and then raised the overall volume to see if the surrounds would have more effect but the M80's still seem to over power them. Is there a way to lower the channel levels on the m80's even further?
Thanks
Samsung 65" 3D LCD TV, Samsung 3D Blu-Ray Disc Player, Denon AVR 3311CI, EP800, M80's, VP150, 4QS8's
|
|
|
Re: Safe Audio Volume?
|
Joined: Nov 2010
Posts: 901
aficionado
|
aficionado
Joined: Nov 2010
Posts: 901 |
Raise the QS levels until you like it! Experiment
|
|
|
Re: Safe Audio Volume?
|
Joined: Mar 2001
Posts: 59
buff
|
buff
Joined: Mar 2001
Posts: 59 |
You would be best to re-calibrate your system manually. Start from the intial set up, select small or large for the mains, small for the center and small for the surrounds. Depending on your main selection, chose the appropriate setting for your subwoofer; I would suggest using 80Hz as your default crossover point. Adjust the distance levels of each speaker to the listening position. Using the test tone, set the system manually to the listening position. Using 0db as your reference, adjust the output of each speaker so that each speaker presents the same output to the listening position. On playing a movie you may find that you might want to increase or decrease the output of your speakers to your preference.
Brent Tombari Axiom Audio Expert
|
|
|
Forums16
Topics24,949
Posts442,508
Members15,619
|
Most Online2,082 Jan 22nd, 2020
|
|
1 members (SirQuack),
1,077
guests, and
3
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|