Low power wiring for LED applications
|
Joined: Sep 2004
Posts: 5,422
axiomite
|
OP
axiomite
Joined: Sep 2004
Posts: 5,422 |
I am hoping to get my LED rope lights wired up in the near future, anyway. I have a controller that handles 3 strips of the LED lights. I've heard that you can try to daisy chain some of the strips together, but you run the risk that by the time you get to the end of the connected pieces, their may be power or color changing signal loss. So....
I am connecting the 3 long strips to their own set of 4-wire "ports" on the controller.
Now for the question: If the normal wire used is 18 gauge for each (4-wire per "port"), can a person use two 24 gauge wires (IE: a single pair from Cat5 wire) for each of the 18 gauge runs?
Cat5 wire for those that don't know consists of 4 pairs (8 runs) of 24 gauge wire.
*) 18 gauge wire is 1.024mm thick
*) 24 gauge wire is 0.511mm thick
*) two 24 gauge wires is the same amount of copper as a single 1.022mm thick wire.
I have a spool of Cat5 wire at home were I could, for example, take the white/blue and blue/white pair, strip the ends, twist the ends together and use that, however I don't want to run the risk of messing anything up. I doubt that heat will be an issue since this is pretty low voltage stuff (12 volts total into the controller, 5 amps out total, that is split among 3 strips).
Would it work safely?
Farewell - June 4, 2020
|
|
|
Re: Low power wiring for LED applications
|
Joined: Jun 2003
Posts: 8,488
axiomite
|
axiomite
Joined: Jun 2003
Posts: 8,488 |
I have no idea. But I can't wait to again learn from your experience. Remember - Pictures.
bibere usque ad hilaritatem
|
|
|
Re: Low power wiring for LED applications
|
Joined: Jan 2011
Posts: 1,291
connoisseur
|
connoisseur
Joined: Jan 2011
Posts: 1,291 |
i think that double or half the current capacity is a difference of 3 gauge numbers: from 18 to 21 is half, and vice versa. the reason is we can't use the wire diameter, it's the surface area of the wire ends that counts. doubling the wire diameter is 4 times the surface area and 4 times the current capacity. two 24 gauge wires in parallel is equivalant to one 21 gauge wire.
|
|
|
Re: Low power wiring for LED applications
|
Joined: Jun 2003
Posts: 8,488
axiomite
|
axiomite
Joined: Jun 2003
Posts: 8,488 |
two 24 gauge wires is the same amount of copper as a single 1.022mm thick wire I don't think that's right. Don't you have to calculate the volume of the cylinder (wire)? Which is - I think - what JB said. Edit: So, based on JB, you'd need 4 24's to equal 1 18.
bibere usque ad hilaritatem
|
|
|
Re: Low power wiring for LED applications
|
Joined: Sep 2004
Posts: 5,422
axiomite
|
OP
axiomite
Joined: Sep 2004
Posts: 5,422 |
Yeah, that does make more sense. Guess I will be buying some wire...
Farewell - June 4, 2020
|
|
|
Re: Low power wiring for LED applications
|
Joined: Feb 2004
Posts: 1,703
connoisseur
|
connoisseur
Joined: Feb 2004
Posts: 1,703 |
I'd be surprised if CAT5 couldn't handle the power of these LEDs, unless you have a crap load of them. When you say 5 amps is that just what the power supply is rated for or what the combined LED's actually draw?
|
|
|
Re: Low power wiring for LED applications
|
Joined: Sep 2004
Posts: 5,422
axiomite
|
OP
axiomite
Joined: Sep 2004
Posts: 5,422 |
The specs are as follows: Input Voltage:12 Volts DC Output Voltage:12 Volts DC Power (Watts):60 W Current (Amps) Output:5 A IR Music Controller 60 Watt 3 Ports With Remote for Color Changing LEDs,3322RGB Although looking at my Amazon order history, I bought 3 of these and I was using one of those included 4 amp power supplies when I tested it a couple of months ago.: 16.4 Ft RGB Color Changing Kit with LED ...rs, 2034rgb Kit They were an all in one package by themselves, but testing them, even with the IR sensors close to each other, they responded with slightly different delays to commands, plus sometimes one wouldn't receive the remote command. Hooking them up to the IR Music Controller meant a single IR "eye" to aim at, and then all were controlled exactly at the same time.
Farewell - June 4, 2020
|
|
|
Re: Low power wiring for LED applications
|
Joined: Feb 2004
Posts: 1,703
connoisseur
|
connoisseur
Joined: Feb 2004
Posts: 1,703 |
Those specs appear to be just what the power supply is capable of. Would need to figure out what the LEDs actually draw to know for sure. I'm just making an educated guess when I say the CAT5 would work.
|
|
|
Re: Low power wiring for LED applications
|
Joined: May 2003
Posts: 2,185
connoisseur
|
connoisseur
Joined: May 2003
Posts: 2,185 |
In theory, I'm sure that CAT5 might work but the problem would be if there's a fire. I'm pretty sure it's not fire rated and probably not to code. If insurance gets involved, it's possible they can deny a claim because of a code violation.
This is why I disconnected some of the lighting in my house when I purchased it 2007, after finding ceiling lights wired with 12 ga speaker wire. Granted it was for standard AC lights that are usually Romex, not the low voltage for your case. But I didn't want to risk it.
|
|
|
Re: Low power wiring for LED applications
|
Joined: Sep 2004
Posts: 5,422
axiomite
|
OP
axiomite
Joined: Sep 2004
Posts: 5,422 |
I decided that I am just going to use a bunch of 14gauge wire I have on a spool. If the crown molding is large enough, I will run two sets of wire for each strip of LED lights as they currently exist. By that, I mean that the wiring is rated for in-wall applications too, so it has a protective outer sheathing. If it is too bulky, then I will take the outer sheathing off and just run the pairs that way.
Farewell - June 4, 2020
|
|
|
Forums16
Topics24,945
Posts442,484
Members15,617
|
Most Online2,082 Jan 22nd, 2020
|
|
0 members (),
1,228
guests, and
6
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|