You are not logged in. [Log In]


Forums » General Discussion » Stereo » Powering LFR's

Page 3 of 3 < 1 2 3
Topic Options
Rate This Topic
#391330 - 03/23/13 10:31 AM Re: Powering LFR's [Re: brwsaw]
J. B. Offline
connoisseur

Registered: 01/19/11
Posts: 1291
Loc: Quebec, Canada
this is done with an adjustment in the receiver named Input Level Adjustment or something similar.
_________________________
See: http://www.blu-ray.com/community/gallery.php?member=Gelli
or: Axiom Gallery

Top
#391331 - 03/23/13 10:36 AM Re: Powering LFR's [Re: brwsaw]
brwsaw Offline
connoisseur

Registered: 10/12/12
Posts: 1773
Loc: Canada
Thanks.
I take another look.
_________________________
Getting closer to an hour a day in my HT.
My precious...

Top
#391355 - 03/24/13 06:44 AM Re: Powering LFR's [Re: brwsaw]
dakkon Offline
connoisseur

Registered: 02/08/04
Posts: 1863
Originally Posted By: brwsaw
Anyone ever meet the 400 watt limit and measure the db at any given distance?
I don't know that I'll need the extra power in my next room.


The amp i am using for my front drivers is rated for 1200W @ 2ohm, the amp i'm using for my rear drivers is rated for 500W @ 4 ohms.

The front amps is a Krell FBP300cx, the rear amp is a krell KAV 250A. My normal volume is about 90-95db in the room, with peaks well over 100db... My room is a great room that is about 17feetX18feet..


Clean power is the most important thing, Clipping is what does damage to speakers, not power....

With that being said, i will admit, i have way more power than i need... But, i'm ok with that :~)

Top
#391364 - 03/24/13 12:42 PM Re: Powering LFR's [Re: brwsaw]
brwsaw Offline
connoisseur

Registered: 10/12/12
Posts: 1773
Loc: Canada
Would the artifacts added from a scratched cd or bad PVR recording be considered clipping or is there another word for it?
I always worry about the times when the audio signal is interupted for a moment.
Iphones and Ipods connected by wire are the worst.


Edited by brwsaw (03/24/13 12:43 PM)
_________________________
Getting closer to an hour a day in my HT.
My precious...

Top
#391369 - 03/24/13 02:19 PM Re: Powering LFR's [Re: brwsaw]
dakkon Offline
connoisseur

Registered: 02/08/04
Posts: 1863


Edited by dakkon (03/24/13 02:19 PM)

Top
#391375 - 03/24/13 04:51 PM Re: Powering LFR's [Re: brwsaw]
brwsaw Offline
connoisseur

Registered: 10/12/12
Posts: 1773
Loc: Canada
Thanks. I've got a handle on clipping because of too little power.
I wonder if the issues mentioned above have the same effect. They can happen at any volume.
_________________________
Getting closer to an hour a day in my HT.
My precious...

Top
#391377 - 03/24/13 06:28 PM Re: Powering LFR's [Re: brwsaw]
dakkon Offline
connoisseur

Registered: 02/08/04
Posts: 1863
not if your amp (voltage source) can handel the input signal. The only time you would have a problem is if you are trying to push the amp beyond it's operating parameters.. You mentioned sudden increases in volume, and artifacts within the source. These are just inputs, if you have a substantial enough amp, you're LFR's will play much lounder than you would ever want them to.. I usually listen to my system at 12-15 or so.. Reference level on my processor is 32.. If that gives you a gauge as to how loud it gets... 12-15 will result in about 90ish db within the room... The only way i would measure the DB in the room at reference level would be with hearing protection. At that point, it would just be an exercise to get a number..

Top
Page 3 of 3 < 1 2 3

Moderator:  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 
Forum Stats

15,224 Registered Members
15 Forums
23,992 Topics
424,050 Posts

Most users ever online:
883 @ 03/04/17 05:06 PM

Top Posters
Ken.C 18044
pmbuko 16437
SirQuack 13567
CV 11677
MarkSJohnson 11437
1 registered (Kevin1)
44 Guests and
3 Spiders online.
Key: Admin, Global Mod, Mod
Newsletter Signup