Previous Thread
Next Thread
Print Thread
Rate Thread
Exposed wires
#393613 06/01/13 06:21 AM
Joined: Oct 2012
Posts: 2,016
Likes: 1
B
brwsaw Offline OP
connoisseur
OP Offline
connoisseur
B
Joined: Oct 2012
Posts: 2,016
Likes: 1
I've taken great care to make sure my power cables do not occupy the same space or touch or cross my other cables but the remainder of my cables run parallel as needed.
All are above the floor/not in wall and are exposed.
Should I be concerned about coax/speaker cable/sub cable/ cat5 cables crossing, touching etc?
The only noise/hum in my system comes from the PVR. Its about to be replaced.




Re: Exposed wires
brwsaw #393615 06/01/13 09:57 AM
Joined: Jan 2011
Posts: 1,291
J
connoisseur
Offline
connoisseur
J
Joined: Jan 2011
Posts: 1,291
basically, i think power cables can all be run together, even tied together, but signal cables should be at least a few inches away from power cables and run parallel for as short a distance as possible.

touching is ok and crossing is very good.

Re: Exposed wires
brwsaw #393639 06/01/13 11:28 PM
Joined: Dec 2003
Posts: 10,420
J
shareholder in the making
Offline
shareholder in the making
J
Joined: Dec 2003
Posts: 10,420
Coax/sub cables are shielded so you really don't have to worry about with them. Cat 5 with twisted pairs is generally ok as well


Jason
M80 v2
VP160 v3
QS8 v2
PB13 Ultra
Denon 3808
Samsung 85" Q70
Re: Exposed wires
brwsaw #393709 06/04/13 05:23 PM
Joined: Sep 2004
Posts: 5,422
axiomite
Offline
axiomite
Joined: Sep 2004
Posts: 5,422
Any time a power cable needs to come near a signal cable, they should be run as perpendicular as possible to make the point that they touch as small as possible.


Farewell - June 4, 2020
Re: Exposed wires
nickbuol #393720 06/04/13 08:21 PM
Joined: Oct 2012
Posts: 2,016
Likes: 1
B
brwsaw Offline OP
connoisseur
OP Offline
connoisseur
B
Joined: Oct 2012
Posts: 2,016
Likes: 1
None of my power cables physically touch the remaining cabling.
Most of my speakers cables, Coax, cat5 cables run in a group around the room as required. They touch several times in several locations.
I've cut each cable long enough to run them through the floor and up walls once I've decided on the locations. There is a loop of cable in the front corners.




Re: Exposed wires
brwsaw #393726 06/05/13 01:01 PM
Joined: Sep 2004
Posts: 5,422
axiomite
Offline
axiomite
Joined: Sep 2004
Posts: 5,422
Just some notes:
Coax is shielded to prevent interference.
CAT5 can be shielded and is inheritly protected from outside signal noise due to its twists. Although, must of that "noise" comes from other pairs in the same CAT5 cable, thus each pair is twisted differently inside the CAT5 cable itself.

Speaker signal wire is potentially your most "powerful" set of wires running in your bundle. You won't see much interference coming into the speaker signal from the other two sources, and those other sources are designed to block signals from leaking in/out.

Long story short, you are fine unless doing really long cable/wire runs.

Now, just remember, a coil of copper wire with electricity running through it is an electro-magnet. Not a strong enough one to worry about though. Just sayin'...


Farewell - June 4, 2020

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,491
Posts434,527
Members15,440
Most Online2,082
Jan 22nd, 2020
Top Posters
Ken.C 18,044
pmbuko 16,437
SirQuack 13,707
CV 11,914
MarkSJohnson 11,451
Who's Online Now
2 members (Kodiak, CV), 576 guests, and 2 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4