Crossover design
|
Joined: Mar 2014
Posts: 1,593 Likes: 1
connoisseur
|
OP
connoisseur
Joined: Mar 2014
Posts: 1,593 Likes: 1 |
Does anyone know how critical it is to maintain the exact components in a crossover design?
I ask because I am about to build some speakers and will likely sustitute higher tolerance parts than were spec'd in the original design. ie. inductors with lower resistance. Resistors with lower inductance etc. than designer spec'd parts.
I have an email into the designer as well but thought I would ask the void for input.
Last edited by Serenity_Now; 01/31/17 10:38 AM.
|
|
|
Re: Crossover design
|
Joined: Jan 2002
Posts: 3,270
connoisseur
|
connoisseur
Joined: Jan 2002
Posts: 3,270 |
Hi Serenity,
Unless you have a technical electronics or engineering degree and the electronic gear to plug in different component values and graph the changes in frequency response and crossover slopes, it's impossible to estimate what effects the substitution of different components will have in a particular crossover design.
I recall watching Ian test different values of crossover components in tweaking the design of an Axiom speaker, and subtle changes in the component values gave the speaker an entirely different midrange response when the speaker was measured and then tested in double-blind listening tests.
The speaker might have been the early M80ti, whose midrange response I was highly critical of (edgy and sibilant on female vocals and brass instruments) and wanted him to change, which he did.
Good luck (and you'll need it) on the home-built speaker design.
Alan
Alan Lofft, Axiom Resident Expert (Retired)
|
|
|
Re: Crossover design
|
Joined: Mar 2014
Posts: 1,593 Likes: 1
connoisseur
|
OP
connoisseur
Joined: Mar 2014
Posts: 1,593 Likes: 1 |
Thanks! I'm not going to stray from the prescribed values, just go from 5% to 1 or 2% parts and larger AWG size on the inductors. After some poking around I see that parts costs escalate quickly, so I'm not going crazy with Mundorf Maximizer Ultimate Sunshine.... Solen Fast Caps (PB, SB in tweeter CCT), Erse Inductors 16awg, Mills Resistors in parallel to double power handling and further tighten tolerances. Pretty much defacto parts express stuff for mid to higher range builds. High value for $ stuff. Won't be cheap, but wont be silly either. Or is it..... Total estimated cost for 3 towers $529 before shipping. Yikes!
|
|
|
Re: Crossover design
|
Joined: Jan 2007
Posts: 10,490 Likes: 116
shareholder in the making
|
shareholder in the making
Joined: Jan 2007
Posts: 10,490 Likes: 116 |
The benefits of tighter component tolerances increase with filter order. A third order filter would benefit greatly but a first order won't.
My advice is to build the kit. Once you've done that, then you can experiment. Try to get the ideal parts list from the designer. The ideal parts list comes from calculated values. The first thing to do is wind your own inductors. These are the most non-ideal component. Then switch to non electrolytic caps.
Alan is right in that a crossover is complex business. I know because I've been involved in the design of passive and active filters - not for loudspeakers. The passive crossover for a loudspeaker incolves a lot of mental masturbation particularly for second and higher orders. Controlling the voice coil via passive means when it's impedance changes as a function of temperature, altitude and input power is darned near impossible.
Hence why active crossovers are the only way to go and that's where the LFR needs to go next.
House of the Rising Sone Out in the mid or far field Dedicated mid-woofers are over-rated
|
|
|
Re: Crossover design
|
Joined: Mar 2014
Posts: 1,593 Likes: 1
connoisseur
|
OP
connoisseur
Joined: Mar 2014
Posts: 1,593 Likes: 1 |
My understanding with active is you need to handle each transducer seperately, including amplification. Too expensive for a 3 channel setup with 3 way towers. I am building external crossover boxes so the driver leads are available for further adventures. Options.
|
|
|
Re: Crossover design
|
Joined: Jan 2007
Posts: 10,490 Likes: 116
shareholder in the making
|
shareholder in the making
Joined: Jan 2007
Posts: 10,490 Likes: 116 |
Separate amps indeed but it looks like you are all set for that . External crossovers also eliminate any concern from magnetic coupling from the drivers including modulation from enclosure vibrations.
House of the Rising Sone Out in the mid or far field Dedicated mid-woofers are over-rated
|
|
|
Re: Crossover design
|
Joined: Jan 2007
Posts: 10,490 Likes: 116
shareholder in the making
|
shareholder in the making
Joined: Jan 2007
Posts: 10,490 Likes: 116 |
I really butchered the spelling on my second last post. Phones and larger fingers don't work well together.
House of the Rising Sone Out in the mid or far field Dedicated mid-woofers are over-rated
|
|
|
Re: Crossover design
|
Joined: Dec 2008
Posts: 6,928
axiomite
|
axiomite
Joined: Dec 2008
Posts: 6,928 |
Over $500 for crossover parts?
You can get an excellent digital crossover for far less than that. You'll need some amps though $$.
Half of communication is listening. You can't listen with your mouth.
|
|
|
Re: Crossover design
|
Joined: Jan 2007
Posts: 10,490 Likes: 116
shareholder in the making
|
shareholder in the making
Joined: Jan 2007
Posts: 10,490 Likes: 116 |
Where do you get the digital X-over from?
Interestingly enough my Onk has two separate outputs per channel for the front. One of the outputs is for bass and mid-range and the other is for the tweeter. You can configure your own X-over in the setup. I've never tried it but have always wondered how well it works.
House of the Rising Sone Out in the mid or far field Dedicated mid-woofers are over-rated
|
|
|
Re: Crossover design
|
Joined: Dec 2008
Posts: 6,928
axiomite
|
axiomite
Joined: Dec 2008
Posts: 6,928 |
MiniDSP, Behringer DCX2496, I'm not sure if BBE still makes one or not. The MiniDSP is supposed to be a really good unit.
Half of communication is listening. You can't listen with your mouth.
|
|
|
Forums16
Topics24,945
Posts442,489
Members15,617
|
Most Online2,082 Jan 22nd, 2020
|
|
0 members (),
1,065
guests, and
1
robot. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|