Get Free, Friendly, Expert Advice
Call 1-866-244-8796 or email

Designed and Manufactured in Canada Since 1980

AxiomAudio Blog

Blind Listening Tests

Sneak Peek into Axiom’s Current Research and Development

Axiom’s Newest Speaker: The In-Ceiling M3

A promise is A promise... Axiom's second home
Greg's pseudo-HT room
Who's Online
2 registered (MarkSJohnson, jmone), 44 Guests and 12 Spiders online.
Key: Admin, Global Mod, Mod
Forum Stats
13355 Members
11 Forums
23042 Topics
407471 Posts

Max Online: 378 @ 02/24/13 04:33 PM
Top Posters
Ken.C 17828
pmbuko 16308
SirQuack 13354
CV 11366
MarkSJohnson 11032
Meanwhile On Facebook

Love this review by Brad C! "Very impressed with my purchase: 2 High Powered M6...

(y) Great review from Tom H of his new surround speakers! "I love the surroun...

22 year-old Axiom System, still in showroom condition! Welcome home, old friends!

The end of a truly unique voice. RIP Joe Cocker - you were part of the soundtr...

Page 2 of 2 < 1 2
Topic Options
Rate This Topic
#144403 - 08/01/06 02:17 AM Re: Is there such a thing as 'too much' for a room [Re: inthedeck]
DrunkenWolf Offline

Registered: 07/25/06
Posts: 133
Loc: Issaquah, WA
Cool, I think I'm going down that path entirely by accident. I landed on a HK 635 that I got for 500 bucks. I got to thinking about it and realized that I'll probably replace receivers every few years to get the latest connections and whiz-bang. I was trying to figure out what to do with the extra $ in my budget. Putting the money an an amp fund sounds reasonable.

Separate amps are something I don't have experience with. How do the connections work? If you just amplified the fronts does that make them overpower the rears?

#144404 - 08/01/06 03:27 AM Re: Is there such a thing as 'too much' for a room [Re: DrunkenWolf]
bridgman Offline

Registered: 08/25/04
Posts: 5495
Loc: Bowmanville, Ontario, Canada
Most midrange and high end receivers have a set of jacks on the back labelled "pre-amp out" or pre-out for short, with one jack for each channel. You run RCA audio cables from the pre-out jacks for the front left and front right channels to the line-in jacks on the power amp, then disconnect those speakers from the receiver and connect them to the speaker-out terminals on the power amp.

Adjust the volume on the power amp until the speakers play at the same level they did before. At this point you will be thinking "same level... so what did I just accomplish ?".

1. Normally the main and center speakers have to play the loudest, so those channels are the ones where your receiver will run out of power first. Bigger amp = they don't run out of power so soon.

2. Since the main speakers are no longer connected to the receiver, they are no longer presenting a load to the power amp stage of the receiver and no longer consuming power from the receiver's power supply. As a result, there will generally be more power available to the other channels, ie they will be able to play a bit louder than before while still sounding clean.

3. If you are running M80 mains, they present a 4 ohm load which some receivers don't like, while all the rest of your speakers will typically be 6-8 ohms. Big-ass power amps seem to handle 4 ohm loads well, so as a result you have a bit more flexibility in choosing receivers, specifically some Yamaha and Pioneer models which are real nice except that they don't always like driving 4 ohm speakers.

Edited by bridgman (08/01/06 03:34 AM)

#144405 - 08/01/06 03:51 AM Re: Is there such a thing as 'too much' for a room [Re: bridgman]
DrunkenWolf Offline

Registered: 07/25/06
Posts: 133
Loc: Issaquah, WA
Thanks for the explaination!

Page 2 of 2 < 1 2

Moderator:  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Home  |  Corporate Info  |  Products  |  Message Board  |  FAQs  |  Warranty  |  Site Map  |  Privacy Statement   |  Contact Us

©2014 Colquhoun Audio Laboratories Limited
All Rights Reserved.