Sub setup + 6'
|
Joined: Mar 2005
Posts: 340
devotee
|
OP
devotee
Joined: Mar 2005
Posts: 340 |
I think that I've read a # of times here that a good rule of thumb when setting up the sub is to add 6' to the distance. Is that correct and why?
|
|
|
Re: Sub setup + 6'
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
I could be mistaken, but I think Jakeman has mentioned to add 3 ft to the actual measurement to account for the DSP circuitry in the EP subs. Also, if your using a Velodyne SMS-1 Digital EQ to flatten out your room response, add another 3ft for a total of 6ft. That is what I've done. My Denon autosetup adds about 12ft to the actual measurement, so far I like Jakeman's suggestions better.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Re: Sub setup + 6'
|
Joined: May 2002
Posts: 10,654
shareholder in the making
|
shareholder in the making
Joined: May 2002
Posts: 10,654 |
Charles, just to expand a bit on the point, the processing in the sub amplifier can cause a slight delay which makes the sound from the sub arrive as if it was significantly farther away than the measured physical distance. Auto calibration systems can measure this difference and my own view would be to rely more on that rather than arbitrary rules of thumb.
-----------------------------------
Enjoy the music, not the equipment.
|
|
|
Re: Sub setup + 6'
|
Joined: Jan 2007
Posts: 10,490 Likes: 116
shareholder in the making
|
shareholder in the making
Joined: Jan 2007
Posts: 10,490 Likes: 116 |
Maybe this is the answer to my "tightness" problem?
|
|
|
Re: Sub setup + 6'
|
Joined: Mar 2005
Posts: 340
devotee
|
OP
devotee
Joined: Mar 2005
Posts: 340 |
I didn't realize this when I started this thread, but the Emotiva doesn't have a distance setting for the sub so all settings are manual. Maybe the new LMC-2 will.
|
|
|
Re: Sub setup + 6'
|
Joined: Jan 2007
Posts: 10,490 Likes: 116
shareholder in the making
|
shareholder in the making
Joined: Jan 2007
Posts: 10,490 Likes: 116 |
So how are you supposed to set the distance setting for the sub using an Emotiva? What do you mean by manual?
|
|
|
Re: Sub setup + 6'
|
Joined: Mar 2005
Posts: 340
devotee
|
OP
devotee
Joined: Mar 2005
Posts: 340 |
You can't set a distance for the sub on the LMC-1. There is a test tone (which doesn't work very well for the sub) and a trim level but you just have to use the volume on the sub to set it and blend it with the other speakers.
|
|
|
Re: Sub setup + 6'
|
Joined: Jan 2007
Posts: 10,490 Likes: 116
shareholder in the making
|
shareholder in the making
Joined: Jan 2007
Posts: 10,490 Likes: 116 |
You are confusing volume with time delay (distance).
Distance is used to set the time delay for the sub and all of the other speakers. Since all of the speakers are not equidistant to you, the pre-amp adjusts for relative delays between the speakers so that sound will arrive at your ears at the same time from all speakers. In practice, this is never really the case but don't worry about that for now.
Volume on the other hand is ajusted using a set-up mic or, better yet, an SPL meter.
If you don't have a way to set distance for your sub, and it is more than a couple of feet further (or closer) from you relative to the front speakers, you may not experience the "tightness" that you should from your sub and it might sound "slow".
|
|
|
Re: Sub setup + 6'
|
Joined: Oct 2005
Posts: 853
aficionado
|
aficionado
Joined: Oct 2005
Posts: 853 |
The other control to use is the delay setting in your receiver if it has one. Auto calibration in those receivers are very unreliable below 100hz owing to acoustical problems in room in the frequency and time domains. The small chips used in the receiver are not robust enought to quickly compute the many iterations required to arrive at accurate settings when using low frequency sine waves. Its more accurate to simply add 3 ft to for each processing step which accounts for the 2.5-3.0 milliseconds of delay before the signal reaches the drivers.
Imprecise auto-equalization below 100hz is something most software providers do not want to discuss in the manuals. The only one who does address the issue is Behringer in their DSP equalizers, who specifically warn against relying on auto settings in the low-mid bass region. Audessey is hoping to address this problem in their new unit which purports to make massive computations that adjust for phase and frequency. Without the use of far more computing power than found in a typical receiver or boxed equalizer I remain highly sceptical that will acheived. Over the years I have never seen any auto-equalized setting for subs that could not be improved with manual tweaking.
Back at the ranch, I've always found its best to shut off the auto-equalization for the low frequencies and rely on the above noted delay control along with manually tweaking room Q and level on parametric equalizers. Its those controls which make an SMS-1 such an effective tool.
To those who don't have an SMS I'd recommend taking measurements with an RS metre after manually adjusting delay/distance and experimenting with placement.
John
|
|
|
Re: Sub setup + 6'
|
Joined: Mar 2005
Posts: 340
devotee
|
OP
devotee
Joined: Mar 2005
Posts: 340 |
Sure. I use test tones and a SPL meter to set the speaker levels. I did think it interesting that there wasn't a sub distance on the processor. That is interesting about the def of "tight" & "slow". I hear that all the time but don't know what it means. I'm trying to tie the terms and the sounds together. Tight to me means crisp and not boomy. I don't know about slow in relation to bass. Does it mean that I hear the bass notes later than I should; that they are out of sync?
|
|
|
Forums16
Topics24,945
Posts442,484
Members15,617
|
Most Online2,082 Jan 22nd, 2020
|
|
0 members (),
1,228
guests, and
6
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|