Previous Thread
Next Thread
Print Thread
Rate Thread
Page 28 of 114 1 2 26 27 28 29 30 113 114
Re: Got Wood?
Murph #288775 01/26/10 09:55 PM
Joined: Dec 2008
Posts: 6,928
axiomite
Offline
axiomite
Joined: Dec 2008
Posts: 6,928
Charles Idea is a good one, IMO. 4 pieces cut with a 'V' at one end to join in the centre. Another alternative might be to make a cross out of square stock with a dado cut into each piece where they join, then after they are secured as one piece, router the inside edges to make it purdy. If you don't mind spending the coin, get a wainscotting bit to make a perfect join...probably not practical unless you have some other projects to use the bit on. Other than that, a tube of caulk for $1.99, can hide a whole lot!


Half of communication is listening. You can't listen with your mouth.
Re: Got Wood?
Murph #288798 01/27/10 01:08 AM
Joined: Dec 2007
Posts: 119
N
veteran
Offline
veteran
N
Joined: Dec 2007
Posts: 119
Cool table! If you have a router table you could use these.

http://www.toolstoday.com/c-354-window-sash-assembly-router-bits.aspx


Don't die with a clean shop!
Re: Got Wood?
NDinUSA #288805 01/27/10 02:46 AM
Joined: Jul 2004
Posts: 4,444
Likes: 16
M
connoisseur
Offline
connoisseur
M
Joined: Jul 2004
Posts: 4,444
Likes: 16
I'd probable keep them square, cut dado's for the side pieces to slide into. Then route the edge profile up to the point where they intersect on a router table. You can then just use a sharp chisel to profile the intersection.

Nice table by the way. Looks great.

Re: Got Wood?
michael_d #288833 01/27/10 10:55 AM
Joined: Sep 2004
Posts: 11,458
shareholder in the making
OP Offline
shareholder in the making
Joined: Sep 2004
Posts: 11,458
Hey Murph, I don't have any helpful suggestions (what else is new?) but I wanted to say that the stand looks awesome! Really, really, nice job!


::::::: No disrespect to Axiom, but my favorite woofer is my yellow lab :::::::
Re: Got Wood?
MarkSJohnson #288837 01/27/10 12:06 PM
Joined: Dec 2003
Posts: 6,331
axiomite
Offline
axiomite
Joined: Dec 2003
Posts: 6,331
I thnk this is what Zimm is suggesting. I'm not a woodworker, but unless this is too difficult or not feasible, IMHO I think mitering the ends of all four pieces would look good, particularly with the curved top edge. It would also echo the mitered corners of the table top.

P.S. That table is really nice.


Jack

"People generally quarrel because they cannot argue." - G. K. Chesterton
Re: Got Wood?
Ajax #295760 03/10/10 11:26 AM
Joined: Sep 2004
Posts: 11,458
shareholder in the making
OP Offline
shareholder in the making
Joined: Sep 2004
Posts: 11,458
[old man voice]This country is going to hell in a handbasket![/old man voice]

Did you not know it wasn't a SawStop saw when you bought it? Then WTF?


::::::: No disrespect to Axiom, but my favorite woofer is my yellow lab :::::::
Re: Got Wood?
MarkSJohnson #295769 03/10/10 02:26 PM
Joined: Dec 2008
Posts: 1,361
connoisseur
Offline
connoisseur
Joined: Dec 2008
Posts: 1,361
As one of the evil ilk of lawyer/inventors I'd be very interested to know the real details of the case. Maybe that plaintiff just hit the jury lotto because you seldom hear of a jury doing something like that. Sometimes you get anti-big business, or certain prejudices that can trigger outlandish rewards, but wood working is not in that realm. You get as many anti-plaintiff mindsets as "hand out the money" mindsets, and it take a majority (if not unanimity) to get the verdict.

Now, a very common lecture in any business course or early law class is the Ford Pinto case - i.e., saving $0.10 per car because that total was higher than the expected payout to the dead and injured of the badly designed part. That kind of documentation will trigger a pissed-off jury to penalize you.

Yes, it is jury nullification to some extent. At the same time, it is a way for society to bring the laws immediately up to the accepted social morals of that little area - one district court. It will either stop there or spread to state legislatures.

I'm too lazy to go see what actually happened here, but I doubt this is a radical shift in America's trip to hell on the wings of a hand-basket. Really, my laziness in researching this rant is more indicative of that fall.

Finally, Mark it is sad to see someone of your potential so addicted to their hobby that they have to read a string of other people's comments - none of which are journalist or have a TV show...how can you trust them – just to get their sawdust high. Get better man.

Oh, and i'm thinking of buying some of those Axiom computer speakers, anybody tried those. I hear they are bright and will cause my McIntosh Amp to trip b/c they are .005 ohms. Guide me.


Panny 3000 PJ, 118" Carada, Denon 3300, PS3, Axiom QS8, PSB 5T, B&W sub, levitating speaker wire
Re: Got Wood?
Zimm #295771 03/10/10 02:49 PM
Joined: Sep 2004
Posts: 11,458
shareholder in the making
OP Offline
shareholder in the making
Joined: Sep 2004
Posts: 11,458
I never even read the comments below the article...


::::::: No disrespect to Axiom, but my favorite woofer is my yellow lab :::::::
Re: Got Wood?
Zimm #295772 03/10/10 02:50 PM
Joined: Dec 2008
Posts: 6,928
axiomite
Offline
axiomite
Joined: Dec 2008
Posts: 6,928
Anyone else notice that all the new table saws seemed to be equipped with a riving knife.


Half of communication is listening. You can't listen with your mouth.
Re: Got Wood?
Adrian #295773 03/10/10 02:51 PM
Joined: Sep 2004
Posts: 11,458
shareholder in the making
OP Offline
shareholder in the making
Joined: Sep 2004
Posts: 11,458
That's by law now....

From that article: "In 2009, Underwriters Laboratories (UL) will require that all new table saw designs include a riving knife."


::::::: No disrespect to Axiom, but my favorite woofer is my yellow lab :::::::
Page 28 of 114 1 2 26 27 28 29 30 113 114

Moderated by  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 

Link Copied to Clipboard

Need Help Graphic

Forum Statistics
Forums16
Topics24,939
Posts442,452
Members15,615
Most Online2,082
Jan 22nd, 2020
Top Posters
Ken.C 18,044
pmbuko 16,441
SirQuack 13,840
CV 12,077
MarkSJohnson 11,458
Who's Online Now
0 members (), 221 guests, and 0 robots.
Key: Admin, Global Mod, Mod
Newsletter Signup
Powered by UBB.threads™ PHP Forum Software 7.7.4