do i set sacd settings in player as in receiver?
|
Joined: Feb 2006
Posts: 28
hobbyist
|
OP
hobbyist
Joined: Feb 2006
Posts: 28 |
Hi everyone, I finally hooked up my RCA cables so I can playback SACD. I have the Denon 3930 dvd player and Yamaha rx 2700 which I listen on the Axiom 80-500.
Do I need to input my receiver settings (speaker distance, speaker level, size. etc) in the Denon settings for the SACD playback? Will that mess up the settings when I watch a dvd? I have been listening to DVD-A music for the last year or so and finally just now got my cables, I didn't have to make any settings change, however, is that because it was going HDMI and not analog like for SACD?
Thanks for your help! Jason
|
|
|
Re: do i set sacd settings in player as in receiver?
|
Joined: Jun 2007
Posts: 4,357
connoisseur
|
connoisseur
Joined: Jun 2007
Posts: 4,357 |
I have an Oppo BDP-83, and it's my understanding that I would have to set the player up with the required speaker distance, size etc., but I don't know if it is player dependent, or if it is dependent on the quality of the analog processing in the component.
I'm probably way off, but I'm sure someone far more knowledgeable than I will chime in and help you out.
The only reasonable argument for owning a gun is to protect yourself from the police.
|
|
|
Re: do i set sacd settings in player as in receiver?
|
Joined: Aug 2009
Posts: 198
veteran
|
veteran
Joined: Aug 2009
Posts: 198 |
Assuming you have more source components than the 3930, I'd set your speaker parameters in the receiver. If 3930 is the only source, then I don't think it matters much.
Sounds like your Yamaha does not support SACD through HDMI, and that is why you are going with the RCA's? Just wondering.
|
|
|
Re: do i set sacd settings in player as in receiver?
|
Joined: Aug 2007
Posts: 3,488 Likes: 9
connoisseur
|
connoisseur
Joined: Aug 2007
Posts: 3,488 Likes: 9 |
Unless your Yamaha rx2700 can perform bass management on multi channel analog channels (which I doubt very much as this is typically a feature of separate processors or very expensive receivers), you will need to configure the bass management in your oppo players.
As for speaker distances, I think it depends if you use some sort of "pure direct" mode, in which case, I think you also need to set the speaker distances (I know my older Onkyo was making this distinction between "multi-channel" (no bass management, but time-delay) and "pure audio" (no bass management, no time-delay).
If your Denon can send DVD Audio on HDMI, why isn't it capable of doing the same for SACD? My Oppo play does both. My Sony players only support analog. Or is it possible you were only listening to the alternative DD/DTS tracks typically also found on DVD Audios?
See Mojo's signature
|
|
|
Re: do i set sacd settings in player as in receiver?
|
Joined: Sep 2004
Posts: 11,458
shareholder in the making
|
shareholder in the making
Joined: Sep 2004
Posts: 11,458 |
Many receivers with 6 analog inputs (5.1) for SACD and such are not able to apply bass management to that input and so it must be done in the player.
::::::: No disrespect to Axiom, but my favorite woofer is my yellow lab :::::::
|
|
|
Re: do i set sacd settings in player as in receiver?
|
Joined: Sep 2004
Posts: 11,458
shareholder in the making
|
shareholder in the making
Joined: Sep 2004
Posts: 11,458 |
Cam, I either expect a call to the Fire Department, or God to appear in your new avatar!
::::::: No disrespect to Axiom, but my favorite woofer is my yellow lab :::::::
|
|
|
Re: do i set sacd settings in player as in receiver?
|
Joined: Jun 2007
Posts: 4,357
connoisseur
|
connoisseur
Joined: Jun 2007
Posts: 4,357 |
The only reasonable argument for owning a gun is to protect yourself from the police.
|
|
|
Re: do i set sacd settings in player as in receiver?
|
Joined: Dec 2008
Posts: 6,928
axiomite
|
axiomite
Joined: Dec 2008
Posts: 6,928 |
Cam, I either expect a call to the Fire Department, or God to appear in your new avatar! ...or Tommy Chong.
Half of communication is listening. You can't listen with your mouth.
|
|
|
Re: do i set sacd settings in player as in receiver?
|
Joined: Aug 2009
Posts: 198
veteran
|
veteran
Joined: Aug 2009
Posts: 198 |
Many receivers with 6 analog inputs (5.1) for SACD and such are not able to apply bass management to that input and so it must be done in the player. Did not know that. Thanks!
|
|
|
Re: do i set sacd settings in player as in receiver?
|
Joined: Feb 2006
Posts: 28
hobbyist
|
OP
hobbyist
Joined: Feb 2006
Posts: 28 |
if I had all denon components such as receiver and dvd player, I could then utilize d-link and that would save using rca cables, however since I'm denon dvd and yamaha receiver there went that.
in my small amt of knowledge I thought the technology wasn't there yet for hdmi and sacd. I thought the only way was to use RCA cables? Please correct me if I am wrong I would love to learn!
The reason for this post is that when I was listening to a SACD,I noticed there was more um...unseamless sound stage? In other words the surrounds were overpowering the fronts/center. Mind you I have allready done the SPL meter and surround setup using AVIA so the initial "setup" has allready been done. As I said in the original post - movies, cd's, and DVD-A sound great and balanced. That is why I was curious because the SACD was unbalanced. Before I went tooling around and changing settings I wanted to make sure I don't create more work for me in the future.
|
|
|
Re: do i set sacd settings in player as in receiver?
|
Joined: Jun 2007
Posts: 4,357
connoisseur
|
connoisseur
Joined: Jun 2007
Posts: 4,357 |
Cam, I either expect a call to the Fire Department, or God to appear in your new avatar! ...or Tommy Chong. LOL. I would rather have Tommy Chong any day!
The only reasonable argument for owning a gun is to protect yourself from the police.
|
|
|
Forums16
Topics24,946
Posts442,494
Members15,617
|
Most Online2,082 Jan 22nd, 2020
|
|
0 members (),
832
guests, and
3
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|