Flat wire speaker wire installation
|
Joined: Apr 2011
Posts: 2
newbie
|
OP
newbie
Joined: Apr 2011
Posts: 2 |
Hello, I am installing 2 conductor flat wire, but made an error in calculation on distance. I am running the wire under baseboards. In order to extend the distance, Is it possible to connect 2 ends of flat wire together in a compact way? And if so, do you have any hints or recommendations on this? Thank you in advance for your assistance! Best regards, Murray
|
|
|
Re: Flat wire speaker wire installation
|
Joined: Aug 2009
Posts: 6,015
axiomite
|
axiomite
Joined: Aug 2009
Posts: 6,015 |
If it was me, I'd solder it. Then just put some electrical tape around it.
|
|
|
Re: Flat wire speaker wire installation
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
You can but shrink connectors now at Home Depot, Menards, etc. Basically they look like a Butt connector, but have solder inside. Works like a charm, just put the wires in each end, untwisted so the strands integrate, then heat with a heat gun or blow driver (if hot enough).
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Re: Flat wire speaker wire installation
|
Joined: Apr 2011
Posts: 2
newbie
|
OP
newbie
Joined: Apr 2011
Posts: 2 |
Thanks CatBrat and Randy for the tips. Randy - I will lokk into the shrink connectors.
|
|
|
Re: Flat wire speaker wire installation
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
I just used a Wagnor heat gun for drying paint, but you want to keep it moving so you don't over cook the shrink stuff. I think they make speacial heat devices for this stuff.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Re: Flat wire speaker wire installation
|
Joined: Dec 2003
Posts: 10,420
shareholder in the making
|
shareholder in the making
Joined: Dec 2003
Posts: 10,420 |
No special devices to heat the stuff that I am aware of, but there is an adapter for heat guns, butane powered solder guns, etc. that curl around the connector to spread out the heat all at once.
Jason M80 v2 VP160 v3 QS8 v2 PB13 Ultra Denon 3808 Samsung 85" Q70
|
|
|
Re: Flat wire speaker wire installation
|
Joined: May 2010
Posts: 310
devotee
|
devotee
Joined: May 2010
Posts: 310 |
Hello, I am installing 2 conductor flat wire, but made an error in calculation on distance. I am running the wire under baseboards. In order to extend the distance, Is it possible to connect 2 ends of flat wire together in a compact way? And if so, do you have any hints or recommendations on this? Thank you in advance for your assistance! Best regards, Murray i recommend that you bite the bullet, remeasure, add a foot or two to that second measurement and purchase and install that. don't start off your installation with mistakes or splices; every point of connection is a potential point of failure, don't add them where they do not need to be! NO SPLICES, don't do it!
SonySXRD55" Marantz AV7702MKII pre-amp Emotiva XPA-5,UPA-2amps, 14 Speakers, All Axiom Oppo 105D&93
|
|
|
Forums16
Topics24,945
Posts442,479
Members15,617
|
Most Online2,082 Jan 22nd, 2020
|
|
0 members (),
935
guests, and
2
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|