You are not logged in. [Log In]


Forums » General Discussion » Technical Questions » Crossover setting for VP180 at 40hz?

Topic Options
Rate This Topic
#392265 - 04/21/13 05:27 PM Crossover setting for VP180 at 40hz?
VoicOfReason Offline
old hand

Registered: 04/19/12
Posts: 78
Loc: Northwest Arkansas
I have always left my VP180 center channel at 60hz crossover. Well, the other day I was re-running Audyssey and accidentally set the center to large and the front M80's to small. I noticed a very nice improvement in the sound. The center sounded more full and rich. I know the best advice is NOT the set the center to FULL, but what about 40hz while leaving the M80's at 60hz?

Does anyone here use this as their default setting?

Any disadvantages?

Thoughts?



Edited by VoicOfReason (04/21/13 05:30 PM)
_________________________
Epson 8350 * Denon 4311CI * XPA-5 * M80/VP180 * 2 QS8's+M2v3-DSX * SVS PC13-Ultra ** Buttkicker LFE

Top
#392276 - 04/21/13 09:25 PM Re: Crossover setting for VP180 at 40hz? [Re: VoicOfReason]
JohnK Offline
shareholder in the making

Registered: 05/11/02
Posts: 10621
Peter, some clarification of what you in fact did is necessary. When the front speakers are set "Small", none of the other speakers, including the center, can be set "Large".
_________________________
-----------------------------------

Enjoy the music, not the equipment.



Top
#392284 - 04/21/13 10:43 PM Re: Crossover setting for VP180 at 40hz? [Re: JohnK]
VoicOfReason Offline
old hand

Registered: 04/19/12
Posts: 78
Loc: Northwest Arkansas
Sorry. Yes, you are correct. It was the crossover I set wrong at first. The center was at 40hz and fronts were at 60hz. It sounds better this way, I think. Any disadvantages? Do soundtracks usually even send a lot of LFE/low level information to the center channel anyway?
_________________________
Epson 8350 * Denon 4311CI * XPA-5 * M80/VP180 * 2 QS8's+M2v3-DSX * SVS PC13-Ultra ** Buttkicker LFE

Top
#392288 - 04/21/13 11:02 PM Re: Crossover setting for VP180 at 40hz? [Re: VoicOfReason]
SirQuack Offline
shareholder in the making

Registered: 01/29/04
Posts: 13567
Loc: Iowa
Also, you never want to lower the crossover (ok to set higher) from the setting that was configured by your receiver after running Audyssey. For ex, if Audyssey reports back to your Denon that the -3dB point of a particular speaker is 80Hz, the Denon would set the speaker as "small" with an 80Hz crossover, as Denon uses 40Hz as the determining factor. You would never lower that value, but raising is ok.
_________________________
M80s-VP180-4xM22ow-4xM3ic-EP600-2xEP350
Anthem AVM60 Outlaw 7700 Emotiva A500 Epson 5040UB



Top
#392290 - 04/21/13 11:26 PM Re: Crossover setting for VP180 at 40hz? [Re: VoicOfReason]
nickbuol Offline
axiomite

Registered: 09/16/04
Posts: 5319
Loc: Marion, IA
My Onkyo receiver sets my VP180 to 40hz every time I've run it. Some time I leave it, sometimes I bump it up to 60 or 80hz. Like Randy states, that is OK, wit Audyssey because you are basically removing calibration extension in the lower frequencies. However, if it sets something to, say, 80hz, and you drop it down to 60hz, Audyssey hasn't done any room calibration down between the original 80hz and your new 60hz setting.
_________________________
http://ht.buol.us
2-M60s, VP180, 8-M3s, SVS 20-39PCi, DIY Sub, 8-Shakers, JVC RS45, Anthem MRX-1120

Top
#392291 - 04/22/13 01:44 AM Re: Crossover setting for VP180 at 40hz? [Re: nickbuol]
VoicOfReason Offline
old hand

Registered: 04/19/12
Posts: 78
Loc: Northwest Arkansas
Yeah, Audyssey sets everything in front to 40hz default, for me.
_________________________
Epson 8350 * Denon 4311CI * XPA-5 * M80/VP180 * 2 QS8's+M2v3-DSX * SVS PC13-Ultra ** Buttkicker LFE

Top
#392296 - 04/22/13 06:24 AM Re: Crossover setting for VP180 at 40hz? [Re: VoicOfReason]
nickbuol Offline
axiomite

Registered: 09/16/04
Posts: 5319
Loc: Marion, IA
It sets my M60s to 60hz in comparison.
_________________________
http://ht.buol.us
2-M60s, VP180, 8-M3s, SVS 20-39PCi, DIY Sub, 8-Shakers, JVC RS45, Anthem MRX-1120

Top

Moderator:  alan, Amie, Andrew, axiomadmin, Brent, Debbie, Ian, Jc 
Forum Stats

15,224 Registered Members
15 Forums
23,993 Topics
424,054 Posts

Most users ever online:
883 @ 03/04/17 05:06 PM

Top Posters
Ken.C 18044
pmbuko 16437
SirQuack 13567
CV 11677
MarkSJohnson 11437
1 registered (norap)
59 Guests and
3 Spiders online.
Key: Admin, Global Mod, Mod
Newsletter Signup