Will Denon 2310ci AVR work with M80 speakers?
|
Joined: Sep 2009
Posts: 3
newbie
|
OP
newbie
Joined: Sep 2009
Posts: 3 |
Hi,
I'm interested in purchasing a pair of M80 speakers that I can keep around for a long time, but my receiver, a Denon 2310ci, is not rated to drive 4 ohm speakers (as far as I can tell). I'm new to this whole 4-ohm-vs-8-vs-6-ohm thing. I tried looking up the stats on even the Denon flagship receiver ($5.5k model) and it didn't seem rated to work with 4 ohm Front speakers either.
Will my receiver work or should I get another or an external amp or what?
Thanks for any help.
|
|
|
Re: Will Denon 2310ci AVR work with M80 speakers?
|
Joined: May 2003
Posts: 18,044
shareholder in the making
|
shareholder in the making
Joined: May 2003
Posts: 18,044 |
Historically, Denons have proven to work just fine with M80s, even down to their cheap receivers. Most receiver aren't rated for 4 ohms for regulatory reasons. When you do get the speakers, whatever you get, leave the receiver set to the highest impedence (ie 8 ohms) you can; anything less will result in current limiting which can damage speakers.
I am the Doctor, and THIS... is my SPOON!
|
|
|
Re: Will Denon 2310ci AVR work with M80 speakers?
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
My Denon 2805 I purchased 6 yrs ago drove my 80's just fine for many years, I am now using a 3808 with no problems. All Denon's, even the lower priced models should have no issues. The 80's are very efficient and play verrrry loud with little power.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Re: Will Denon 2310ci AVR work with M80 speakers?
|
Joined: Sep 2009
Posts: 3
newbie
|
OP
newbie
Joined: Sep 2009
Posts: 3 |
Thanks for your rapid responses -- I'll go ahead with the purchase.
|
|
|
Re: Will Denon 2310ci AVR work with M80 speakers?
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
Are you ordering from the Factory Outlet? You will save 10%, if you don't mind a slight delay...
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Re: Will Denon 2310ci AVR work with M80 speakers?
|
Joined: Dec 2008
Posts: 6,928
axiomite
|
axiomite
Joined: Dec 2008
Posts: 6,928 |
No problem with the Denon powering the M80s, just keep it on the 8 ohm setting as Ken mentioned. Many of us here have asked the same question in the past and it's not an issue for the Denons to run these speakers.
Half of communication is listening. You can't listen with your mouth.
|
|
|
Re: Will Denon 2310ci AVR work with M80 speakers?
|
Joined: Sep 2009
Posts: 3
newbie
|
OP
newbie
Joined: Sep 2009
Posts: 3 |
I'm having trouble understanding the Denon manual. How do I ensure it's set to 8 ohm?
Thanks for the help.
|
|
|
Re: Will Denon 2310ci AVR work with M80 speakers?
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
I don't think the Denon's have this setting, I don't believe my 2805 or current 3808 have one. Some other brands like Onkyo have this setting.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Re: Will Denon 2310ci AVR work with M80 speakers?
|
Joined: Dec 2008
Posts: 6,928
axiomite
|
axiomite
Joined: Dec 2008
Posts: 6,928 |
Denon uses the phrase "Low Impedence Drive Capability". I believe all their AVR's have this in their specs so ie. it probably negates needing a switch, my 2809 doesn't have one but my older receiver(JVC) did.
Half of communication is listening. You can't listen with your mouth.
|
|
|
Re: Will Denon 2310ci AVR work with M80 speakers?
|
Joined: Jan 2004
Posts: 13,840 Likes: 13
shareholder in the making
|
shareholder in the making
Joined: Jan 2004
Posts: 13,840 Likes: 13 |
Funny you mention JVC, I was just going through some old boxes in my storage room. Came across my old Infinity Bookshelf speakers, Advent center, and JVC Pro Logic receiver, still works great..maybe I should hook it up out in the garage for when I'm working on projects.
M80s VP180 4xM22ow 4xM3ic EP600 2xEP350 AnthemAVM60 Outlaw7700 EmoA500 Epson5040UB FluanceRT85
|
|
|
Forums16
Topics24,945
Posts442,487
Members15,617
|
Most Online2,082 Jan 22nd, 2020
|
|
1 members (rrlev),
561
guests, and
3
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
|
|